This document is an owner's manual for a remote controller designed for an air conditioning unit. It provides comprehensive instructions on how to use, maintain, and troubleshoot the remote controller and its associated air conditioner functions.
The manual begins with an "Important Note" thanking the user for purchasing the air conditioner and advising them to read the manual carefully before operation, and to save it for future reference.
The "Table of Contents" outlines the manual's structure, covering:
- Remote Controller Specifications
- Handling the Remote Controller
- Buttons and Functions
- Remote Screen Indicators
- How to Use Basic Functions
- How to Use Advanced Functions
Handling the Remote Controller
This section details the process of inserting and replacing batteries in the remote control. Users are instructed to slide the back cover downward, insert two R03/LR03 dry batteries, ensuring correct polarity (+ and -), and then slide the cover back into place.
"Battery Notes" provide important tips for optimal product performance:
- Do not mix old and new batteries, or batteries of different types.
- Remove batteries if the remote control will not be used for more than 2 months.
"Battery Disposal" advises users not to dispose of batteries as unsorted municipal waste and to refer to local laws for proper disposal.
"Tips for Using Remote Control" highlights operational guidelines:
- The remote control must be used within 8 meters of the unit.
- The unit will beep when a remote signal is received.
- Curtains, other materials, and direct sunlight can interfere with the infrared signal receiver.
- Batteries should be removed if the remote will not be used for more than 2 months.
"Notes for Using Remote Control" includes regulatory compliance information:
- The device may comply with local national regulations.
- In Canada, it complies with CAN ICES-3(B)/NMB-3(B).
- In the USA, it complies with part 15 of the FCC Rules, stating that operation is subject to two conditions: (1) the device may not cause harmful interference, and (2) it must accept any interference received, including undesired operation.
- The equipment has been tested and found to comply with Class B digital device limits, designed to provide reasonable protection against harmful interference in residential installations.
- It generates, uses, and can radiate radio frequency energy, and if not installed and used according to instructions, may cause harmful interference to radio communications.
- There is no guarantee that interference will not occur in a particular installation.
- If interference occurs, users are encouraged to try corrective measures such as reorienting/relocating the receiving antenna, increasing separation between equipment and receiver, connecting the equipment to a different circuit, or consulting a dealer/experienced radio/TV technician.
- Changes or modifications not approved by the party responsible for compliance could void the user's authority to operate the equipment.
This section provides a detailed overview of the remote control's buttons and their functions, serving as a quick start guide. It emphasizes familiarizing oneself with the remote before using the air conditioner and refers to later sections for detailed instructions.
Key buttons and their functions include:
- TEMP ▼: Decreases temperature in 1°C (1°F) increments, with a minimum of 16°C (60°F).
- ON/OFF: Turns the unit on or off.
- MODE: Scrolls through operation modes: AUTO → COOL → DRY → HEAT → FAN.
- SWING: Starts and stops louver movement.
- SLEEP: Saves energy during sleeping hours.
- DIRECT: Used to set airflow direction.
- ECO: Enters the energy-efficient mode.
- CLEAN: Used to clean the air conditioner evaporator to prevent frosting.
- TEMP ▲: Increases temperature in 1°C (1°F) increments, with a maximum of 30°C (86°F).
- NOTE: Pressing TEMP ▼ & TEMP ▲ simultaneously for 3 seconds alternates the temperature display between °C and °F.
- FAN SPEED: Selects fan speeds in the order: AUTO → LOW → MED → HIGH.
- TIMER ON: Sets a timer to turn the unit on.
- TIMER OFF: Sets a timer to turn the unit off.
- TURBO: Enables the unit to reach a preset temperature in the shortest possible time.
- LED: Turns the indoor unit's LED display on and off.
- NOTE: Holding the LED button for five seconds alternates the temperature display of the indoor unit between setting temperature and room temperature (some units).
- LOCK: Pressing DIRECT & TIMER OFF simultaneously for 5 seconds locks the keyboard. Pressing them together for 2 seconds unlocks it.
A "Special Note" clarifies:
- Button designs may differ slightly from the examples shown.
- If the indoor unit lacks a particular function, pressing that button on the remote will have no effect.
- In cases of discrepancies between the "Remote controller Manual" and "USER'S MANUAL" on function descriptions, the "USER'S MANUAL" description prevails.
Remote Screen Indicators
This section explains the information displayed on the remote controller's screen when powered up.
- Mode display: Icons indicate AUTO, COOL, DRY, HEAT, and FAN modes.
- Transmission indicator: An icon appears when data is transmitted.
- Remote ON indicator: An icon shows when the remote controller is ON.
- TIMER ON/OFF indicators: Icons show when TIMER ON or TIMER OFF times are set.
- Temperature/Time display: Shows set temperature, room temperature, or time under TIMER setting.
- ECO indicator: Appears when the ECO feature is activated.
- Lock indicator: Shows when all current settings are locked.
- Follow Me indicator: Appears when the Follow Me feature is activated (some units).
- SLEEP indicator: Appears when the SLEEP feature is activated.
- FRESH indicator: Appears when the FRESH feature is activated (some units).
- TURBO indicator: Appears when the TURBO feature is activated.
- Horizontal louver auto swing display: An icon indicates horizontal louver auto swing.
- Vertical louver auto swing display: An icon indicates vertical louver auto swing (some units).
- Fan speed indication: Icons for HIGH, MED, LOW, and NO display (Auto fan speed).
A "Note" clarifies that all indicators are for clear presentation, and only relevant signs are shown during actual operation.
How to Use Basic Functions
This section provides step-by-step instructions for operating the air conditioner's basic functions.
"Attention!" advises ensuring the unit is plugged in and powered before operation.
Setting Temperature:
- The operating temperature range is 16-30°C (60-86°F).
- Temperature can be increased or decreased in 1°C (1°F) increments.
AUTO Mode:
- The unit automatically selects COOL, FAN, HEAT, or DRY based on the set temperature.
- Press MODE to select AUTO.
- Set desired temperature using TEMP ▲ or TEMP ▼.
- Press ON/OFF to start the unit.
- NOTE: FAN SPEED cannot be set in AUTO mode.
COOL Mode:
- Press MODE to select COOL mode.
- Set desired temperature using TEMP ▲ or TEMP ▼.
- Press FAN to select fan speed: AUTO, LOW, MED, or HIGH.
- Press ON/OFF to start the unit.
DRY Mode (dehumidifying):
- Press MODE to select DRY.
- Set desired temperature using TEMP ▲ or TEMP ▼.
- Press ON/OFF to start the unit.
- NOTE: FAN SPEED cannot be changed in DRY mode.
FAN Mode:
- Press MODE to select FAN mode.
- Press FAN to select fan speed: AUTO, LOW, MED, or HIGH.
- Press ON/OFF to start the unit.
- NOTE: Temperature cannot be set in FAN mode, so the remote's LCD screen will not display temperature.
HEAT Mode:
- Press MODE to select HEAT mode.
- Set desired temperature using TEMP ▲ or TEMP ▼.
- Press FAN to select fan speed: AUTO, LOW, MED, or HIGH.
- Press ON/OFF to start the unit.
- NOTE: As outdoor temperature drops, the unit's HEAT function performance may be affected. It's recommended to use the air conditioner with other heating appliances in such cases.
Setting the TIMER (TIMER ON/OFF):
This function sets the amount of time after which the unit will automatically turn on/off.
TIMER ON setting:
- Press TIMER ON to initiate the ON time sequence.
- Press TEMP up or down multiple times to set the desired time for the unit to turn on.
- Point the remote to the unit and wait 1 second; TIMER ON will be activated.
TIMER OFF setting:
- Press TIMER OFF to initiate the OFF time sequence.
- Press TEMP up or down multiple times to set the desired time for the unit to turn off.
- Point the remote to the unit and wait 1 second; TIMER OFF will be activated.
NOTE on Timer Settings:
- When setting TIMER ON or TIMER OFF, the time increases in 30-minute increments up to 10 hours, then in 1-hour increments from 10 to 24 hours. (e.g., 5 presses for 2.5h, 10 presses for 5h). The timer reverts to 0.0 after 24 hours.
- To cancel either function, set its timer to 0.0h.
TIMER ON & OFF setting (example):
This section illustrates how to set both TIMER ON and TIMER OFF, with time periods referring to hours after the current time. An example shows setting the unit to turn on 2.5 hours later and turn off 5 hours later, given a current time of 1:00 PM.
How to Use Advanced Functions
This section details the air conditioner's advanced features.
Swing function:
- Pressing SWING starts the horizontal louver swinging up and down automatically. Pressing it again stops the movement.
- Pressing SWING for more than 2 seconds activates the vertical louver swing function (model dependent).
Airflow direction:
- Each press of the DIRCT button adjusts the louver by 6°. Continue pressing until the preferred direction is reached.
LED DISPLAY:
- Pressing LED DISPLAY turns the indoor unit's LED display on or off.
- Pressing LED DISPLAY for more than 5 seconds (some units) makes the indoor unit display the actual room temperature. Pressing it again for more than 5 seconds reverts to displaying the setting temperature.
Active Clean Function:
- Pressing CLEAN activates the Active Clean Technology. This feature washes away dust, mold, and grease that cause odors by automatically freezing and then rapidly thawing the frost on the heat exchanger.
ECO function:
- Pressing ECO under COOL Mode enters the energy-efficient mode (for model RG51A(2)/E).
- Note: This function is only available under COOL mode.
- In cooling mode, pressing ECO automatically adjusts the temperature to 24°C/75°F and fan speed to Auto to save energy (only if the set temperature is less than 24°C/75°F). If the set temperature is above 24°C/75°F, pressing ECO changes the fan speed to Auto, but the set temperature remains unchanged.
- NOTE: Pressing ECO, modifying the mode, or adjusting the set temperature to less than 24°C/75°F will stop ECO operation. Under ECO operation, if the set temperature is 24°C/75°F or above, it may result in insufficient cooling. To stop it, press ECO again.
SHORTCUT function:
- Used to restore current settings or resume previous settings (for model RG51B(2)/E).
- When the remote controller is on, pressing SHORTCUT automatically reverts the system to previous settings, including operating mode, setting temperature, fan speed level, and sleep feature (if activated).
- If held for more than 2 seconds, the system automatically restores the last operation settings.
SLEEP function:
- The SLEEP function decreases energy use while sleeping, adjusting temperature settings for comfort.
- This function can only be activated via remote control.
- The sleep function is not available in Fan or Dry mode. Users are referred to the OWNER'S MANUAL for more details.
Silence function:
- Pressing FAN SPEED for more than 2 seconds activates/disables the Silence function (some units).
- Due to low frequency compressor operation, this mode may result in insufficient cooling and heating capacity.
- Pressing ON/OFF, Mode, Sleep, Turbo, or Clean buttons while in Silence mode will cancel the function.
The document concludes with a note that "The design and specifications are subject to change without prior notice for product improvement. Consult with the sales agency or manufacturer for details." It also includes a product code and date.
Need help?
General
To Next Page
