Midland BTX1 Manual

5 - Midland BTX1 midlandusa.com
How to pair two BTX1 units
The two units supplied in the same BTX1 box, are already paired and ready to
use, which mean you don’t need to perform this procedure. The units are already
paired using the Middle button.
If the devices are not part of the same kit, or the units has been purchased sepa-
rately, you need to rst pair them in order to use them together.
To pair the BTX1 to another BTX1 unit
To pair the BTX1 to another BTX1 unit, you must rst enter the setup mode:
1. Turn o the unit
2. Press and hold down the middle button about 7 sec., until the Red light is on
permanently.
3. Now press the Middle button for 3 seconds. The Blue and Red light will ash.
4. Do the same procedure on the other unit. When successfully paired, each unit
will have the Blue light on for one second and than go back to the setup mode
(Red light always on).
5. Now the pairing procedure is complete, you need to exit the setup mode be-
fore you can use the units.
6. Double click on the Middle button, the Red light will turn o and the Blue
light will start ashing.
You can use now your BTX1.
How to use the Intercom
To use the intercom feature, be sure both units are turned on and correctly paired
together.
Manual activation
Press the Middle button on one of the two units. Communication is enabled and
remains active until you press again the middle button. The intercom needs a few
seconds to activate. You will hear a beep tone when the intercom is open.
Voice activation (VOX)
Simply start talking to open communications. Expect a few seconds delay. If
there is no conversation the intercom will be closed after 40 seconds. If needed
you can close the intercom manually without waiting 40 seconds (just press the
middle button).
If needed, you can temporarily disable the VOX feature simply by pressing the
Backward button for 7 sec. Two audible beeps will advise you when the VOX is
disabled. To turn the VOX on again, just press the same button, one beep sound
will advise you that the VOX is now active (or just turn the unit o and on again).
Adjusting the volume
Your Midland BTX1 uses AGC technology, which automatically adjusts the listen-
ing volume in relation to background noises.
However, it is also possible to manually adjust the volume by means of the “Vol-
ume +” and “Volume -“buttons.
Attention: Volume can be adjusted only when an audio connection is active.
Attention: The volume buttons (Vol + and Vol -) cannot be used to adjust the
volume of the wired audio source. The AGC system with automatically increase the
volume on higher speed.
How to pair the BTX1 to Midland BT line units
The BTX1 is compatible with all the BT line unit from Midland. You can pair the
BTX1 to a BT2, BT1 or BTX2 unit and the max distance of the intercom is dened
from the lower possible.
To pair the BTX1 to another BT line unit, you must rst enter the setup mode:
1. Turn o the unit
2. Press and hold down the Middle button about 7 sec., until the Red light is on
permanently.
3. Now press the Middle button for 3 seconds. The Blue and Red light will ash.
4. Follow the procedure on the other unit’s instruction manual (normally you can
use the “Volume +” button on all the previous BT line units).
5. When successfully paired, each unit will have the Blue light on for one second
and than go back to the setup mode (Red light always on).
Exit the setup mode from both units before you can use them: for BTX1 double
click on the Middle button, the Red light will turn o and the Blue light will start
ashing. For the other devices of BT line, please refer to their own user manual.
A- Manual activation
Mode Forward button Middle button Rear button
Intercom Short press: Open/Close intercom to paired
raider
Long press: Change mode
Long press: Toggle on/o wired

Midland BTX1 Specifications

General

FM radio	-
USB port	Yes
Maximum range	10 m
Channels quantity	- channels
Product color	Black
Protection features	Water resistant
Quantity	2

Weight and Dimensions

Weight	- g