Milwaukee 4004 User Manual

TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND OPERATOR'S
MANUAL.
AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE ET BIEN
COMPRENDRE LE MANUEL DE L'UTILISATEUR.
PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER Y ENTENDER EL
MANUAL DEL OPERADOR.
OPERATOR'S MANUAL
MANUEL de L'UTILISATEUR
MANUAL del OPERADOR
HEAVY-DUTY DIAMOND CORING EQUIPMENT
EXTRA ROBUSTE OUTILLAGE DE CAROTTAGE AU DIAMANT
EQUIPO DE PERFORACION CON PUNTAS DE DIAMANTE PARA
TRABAJOS PESADOS
DYMODRILLS
FOREUSES DYMODRILL
DYMODRILLS
Cat. No. 4004 20A
Cat. No. 4005 20A
Cat. No. 4079 20A
Cat. No. 4090 15A
Cat. No. 4094 20A
Cat. No. 4096 20A
Cat. No. 4097-20 15A
DYMORIGS
OUTILLAGE DYMORIG
DYMORIGS
Cat. No. 4115 Small base
Petite base
Base pequeña
Cat. No. 4125 Small base
Petite base
Base pequeña
Cat. No. 4120 Large base
Grande base
Base grande
Cat. No. 4130 Large base
Grande base
Base grande

Milwaukee 4004 Specifications

General

Brand	Milwaukee
Model	4004
Category	Drill
Language	English

Summary

General Power Tool Safety Warnings

Work Area Safety

Electrical Safety

Personal Safety

Power Tool Use and Care

Specific Safety Rules for Diamond Drilling

Diamond Drilling Safety Precautions

Covers water use, electrical contact, ear protection, bit jamming, and securing methods.

Chemical Exposure Warning

Grounding and Electrical Safety

Grounded Tool Safety

Details grounding requirements and risks for tools with 3-prong plugs.

Double Insulated Tool Safety

Explains safety features and requirements for tools with 2-prong plugs.

GFCI Requirement for Coring

Stresses the importance of using GFCI with diamond coring equipment for safety.

Extension Cord Guidelines

Assembly Instructions

Dymorig/Vac-U-Rig Stand Assembly (Cat. No. 4125/4130)

Dymorig/Vac-U-Rig Stand Assembly (Cat. No. 4115/4120)

Mounting Dymodrill Motor to Stand

Motor Mounting Bracket and Spacer Assembly

Details attaching the motor to the stand using brackets or optional spacer assemblies.

Mounting the Meter Box

Adjusting Gib Screws

Core Bit Selection and Installation

Assembling Water Shut-Off Valve

Methods for Securing Equipment

Securing Warning

Emphasizes the critical need to secure the rig to prevent injury.

Horizontal Coring (Walls)

Vertical Coring (Floors)

Operation Procedures

Securing Equipment: Expansion-Type Anchor

Details on using expansion anchors for securing the rig to the work surface.

Vacuum System Assembly and Use

Instructions for setting up and using the vacuum system for securing the rig.

Expansion-Type Anchor Securing (Cat. No. 4115/4120)

Specific instructions for securing the rig with expansion anchors on these models.

Vacuum System Operation

Vacuum Gauge Reading Warning

Warns against coring if the vacuum gauge reads less than 20 inches of mercury.

Adequate Water Flow Requirement

Meter Box Functionality

Shear Pin and Clutch Operation

Coring Procedure

General Coring Steps

Outlines the sequence for selecting bits, securing the rig, and adjusting speed.

Water Flow Adjustment

Bit Penetration and Pressure

Guidance on applying steady pressure, using the ammeter, and handling vibration.

Completing the Cut and Bit Removal

Retrieving Cores and Deep Coring

Diamond Coring Factors

Factors Influencing Performance

Operator Technique

Advice on applying consistent pressure, avoiding impacts, and diagnosing vibration.

Water's Role in Coring

Diamond Core Bits - Break-in and Usage

Bit Glazing and Motor Shear Pins

Causes of Bit Glazing

Sharpening Procedure for Core Bits

Effects of Steel in Coring

Maintenance Procedures

General Tool Maintenance