1
ENGLISH
JSPE 90 X
You have high standards and expect to purchase quality goods – quality offered by
Milwaukee. We have built a durable and reliable electric power tool for you.
Please read the instructions for use before first operation so you can handle your
power tool effectively and safely. We are sure that buying an Electric Power Tool
from Milwaukee was the right choice!
JSPE 90 X JSPE 90 X
(110 V–120 V) (220 V–240 V)
Cutting depth max. in:
Soft– wood 110 mm 110 mm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hard–wood 80 mm 80 mm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Steel 10 mm 10 mm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Aluminium 25 mm 25 mm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Nominal power 600 W 710 W. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Stroke rate under no-load 550–2700 min
-1
550–2700 min
-1
. . . . . . . .
Lengths of stroke 26 mm 26 mm. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bevel cuts up to 45
o
45
o
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Weight 2,2 kg 2,2 kg. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
J Please pay attention to the safety instructions in the attached leaflet!
J Dust that arises when working on material containing asbestos or stonework
containing crystalline silicic acid is harmful to the health. Please follow accident
prevention regulations.
J Appliances used at many different locations including open air must be connected
via a current surge preventing switch.
J Always use the protective shields on the machine.
J Always disconnect the plug from the socket before carrying out any work on the
machine.
J Always wear goggles when using the machine. It is recommended to wear gloves,
sturdy non slipping shoes and apron.
J Sawdust and splinters must not be removed while the machine is running.
J Do not pierce the motor housing as this could damage the double insulation (use
adhesives).
J Keep mains lead clear from working range of the machine. Always lead the cable
away behind you.
J Only plug-in when machine is switched off.
J Dust that arises when working on wood or using the tool on industrial material can be
dangerous to health. In this case connect the tool to a suitable suction device.
J Do not use cracked or distorted saw blades.
Typically the A-weighted noise levels of the tool are:
Sound pressure level = 87 dB (A). Sound power level = 100 dB (A).
Wear ear protectors! Measured values determined according to EN 50 144.
Typically the hand-arm vibration is below 2.5 m/s
2
.
Measured values determined according to EN 50 144.
This jig saw can cut wood, plastic and metal; it can cut straight lines, bevels, curves,
and internal cut-outs.
Do not use this product in another way as stated for normal use.
Connect only to a single-phase AC current supply and only to the mains voltage
specified on the rating plate. Connection to sockets without earth protection is
possible as the appliance features protective insulation to DIN 57 740/ VDE 0740
and CEE 20. Radio suppression complies with the European standard EN 55014.
When fitting the plug, make sure that the brown (live) wire of this appliance is
connected to the plug terminal marked L or coloured red, and the blue (neutral) wire
of this appliance is connected to the plug terminal marked N or coloured black.
Under no circumstances must the wires of this appliance be connected to the earth
terminal of the plug marked either E, with the earth symbol or coloured green or
green/yellow.
Introduction
Technical Data
Advice for your
safety
Measured sound
value
Measured
vibration value
Use
Mains
connection
To Next Page
Loading...
