Mimosa 0262348 User Manual

• Before installing please contact your local council for semi permanent structure requirements.
• For permanent fixture contact your local council and use appropriate fixings.
• This gazebo is a Semi-Permanent structure. Damage caused by extreme weather conditions including heavy rain or high winds is not
covered under warranty.
• Please carefully read all instructions before assembly and use.
• Please separate and identify all parts, ensuring that you have all parts listed.
• To avoid damage to your gazebo, it is recommended that you assemble it on a clean, protected surface.
• Washers must be used when indicated during the assembly process.
• Loosely tighten the nuts and then securely tighten when all are in position. Be careful not to over tighten the nuts during assembly.
• As an added precaution we strongly recommend you tighten any loose components after an initial period of use (around 3-6 months).
For assured longevity and safe use of your gazebo, we recommend regular checking and tightening of any bolts.
IMPORTANT SAFETY INSTRUCTIONS
• The ground for erecting and anchoring the gazebo is required to be a level, solid and a safe surface.
• Beware of existing utilities underground.
• Keep away from any electrical installations and transportation devices.
• Never climb, sit, or stand on the structure.
Please carefully read the below warnings and instructions.
Save the instructions for future reference.
!
MULLALOO ALUMINIUM
GAZEBO
Assembly Instructions
Item No.:0262348

Mimosa 0262348 Specifications

General

Brand	Mimosa
Model	0262348
Category	Outdoor Furnishing
Language	English

Summary

General Warnings and Safety Precautions

Step 01: Assemble Leg Base Covers

Connecting Leg Base Covers to Leg Tubes

Attach leg base covers (V) to leg tubes (A) using bolts (BB).

Step 02: Connect Roof Frames

Joining Roof Frames B and B1

Connect roof frames (B & B1) using bolts (AA).

Step 03: Assemble Supporting Frames

Connect Roof Frames B2/B3 with Supporting Frame H

Connect roof frames (B2 & B3) with supporting frame (H) using bolts (BB).

Step 04: Secure Leg Tubes to Roof Frame

Secure Leg Tubes (A) to Roof Frame (B & B1)

Secure leg tubes (A) to roof frame (B & B1) using bolts (DD).

Step 05: Secure Leg Tubes to Upper Roof Frame

Secure Leg Tubes (A) to Roof Frame (B2 & B3)

Secure leg tubes (A) to roof frame (B2 & B3) using bolts (DD).

Step 06: Install Incline Stabiliser Braces

Connect Stabiliser Braces (J) to Frame

Connect incline stabiliser braces (J) to roof frame and leg tubes using bolts (CC) and (AA).

Step 07: Attach Corner Brackets

Join Corner Brackets (Q) to Roof Frame

Join corner brackets (Q) to the roof frame using bolts (FF).

Step 08: Connect Supporting Plates

Attach Supporting Plates (R & R1) to Leg Tubes

Connect supporting plates (R & R1) to leg tubes (A) using bolts (AA).

Step 09: Roof Structure Assembly

Connect Angled Brackets (P) to Roof Frame (C & C1)

Insert angled connection bracket (P) into roof frame (C & C1) and tighten bolts (AA).

Attach Side Roof Tubes (E) to Roof Frame (C & C1)

Connect side roof tubes (E) and roof frame (C & C1) using bolts (DD).

Step 10: Supporting Frame to Roof Frame Connection

Attach Supporting Frames (H) and Plates (R) to Roof Frame (C & C1)

Connect supporting frames (H) and plates (R) to roof frame (C & C1) using bolts (AA).

Step 11: Roof Frame D & D1 Assembly

Connect Roof Frames (D & D1) and Cover with Edge Panels (M)

Connect roof frames (D & D1) with bolts (CC) and nuts (GG), cover with edge panels (M) using bolts (AA).

Step 12: Connect Roof Frame D to Supporting Frame H

Attach Roof Frame (D) to Supporting Frame (H)

Connect roof frame (D) to supporting frame (H) using bolts (AA).

Step 13: Attach Middle Roof Components

Connect Fittings (S) and Tubes (F) with Bolts (AA)

Attach middle cape corner fittings (S) and middle roof tube (F) using bolts (AA).

Step 14: Connect Middle Roof Tubes

Attach Middle Roof Tubes (F) to Roof Frame

Connect the middle roof tubes (F) to the roof frame using bolts (AA).

Step 15: Connect Supporting Frames to Side/Middle Roof Tubes

Attach Supporting Frames (G) to Roof Tubes (E & F)

Connect supporting frames (G) to side roof tubes (E) and middle roof tubes (F) using bolts (AA).

Step 16: Install Roof Edge Panels and Cover Plates

Connect Cover Plates (N) and Edge Panels (K) to Frame (C & C1)

Attach cover plate (N) and roof edge panel (K) to roof frame (C & C1) using bolts (AA).

Cover Roof Edge Panels (K) on Frame (D & D1)

Cover roof edge panels (K) on roof frame (D & D1) using bolts (BB).

Step 17: Install Roof Panels

Secure Roof Panels (W) with Hardware

Install roof panels (W) using bolts (EE), washers (JJ & HH), and nuts (GG).

Step 18: Attach Final Roof Edge Components

Connect Edge Panels (L), Tubes (E), and Brackets (U)

Connect roof edge panels (L), side roof tubes (E), and corner brackets (U) using bolts (AA).

Connect Edge Panels (L), Tubes (F), and Brackets (T)

Connect roof edge panels (L), middle roof tubes (F), and middle brackets (T) using bolts (AA).

Step 19: Attach Remaining Roof Edge Panels

Connect Edge Panels (L & L1) and Brackets (T)

Connect roof edge panels (L & L1), middle roof tubes (F), and middle brackets (T) using bolts (AA).

Step 20: Secure Gazebo to Ground

Anchor Gazebo with Bolts (KK)

Secure the gazebo to the ground using bolts (KK) after checking local regulations.