The provided document is a product manual for the X-LIMITED Personal Mobility device, also known as DUALTRON X LIMITED, manufactured by MINIMOTORS. This device appears to be a high-performance electric scooter.
Function Description
The X-LIMITED Personal Mobility device is an electric scooter designed for personal transportation. It features a robust build with dual motors, hydraulic brakes, and advanced suspension, suggesting it's built for power, speed, and comfort across various terrains. The scooter includes a dashboard with a lampholder, multi-switch, and USB port on the handlebars. It has a headlight, running headlight, front and rear turn signals, and ambient lights for visibility. A horn is also integrated for safety. The device is foldable for easier storage and transport. It supports connection to a DUALTRON APP via Bluetooth for enhanced control and monitoring.
Important Technical Specifications
Model: DUALTRON X LIMITED
Dimensions (Length x Width x Height):
- Unfolded: 1450x648x1400mm
- Folded: 1450x358x775mm
Net Weight: 82.9kg
Max. Load: 150kg
Recommended Age: 14-60 years old
Wheelbase: Approx. 1100mm
Ground Clearance: Approx. 190mm
Drive System: Two-wheel drive
Max. Speed: Around 110km/h
Theoretical Range: Around 170km (tested with 75 kg load, 25°C, 25 km/h on pavement)
Typical Range: Around 140km (tested with 75 kg load, 25°C, 50 km/h on pavement)
Max. Slope: Around 70% (35°)
Traversable Terrain: Asphalt/flat pavement; obstacles < 5 cm; gaps < 5 cm
Operating Temperature: -5 to 45°C
Storage Temperature: -20 to 50°C
Battery:
- Main Battery: 84V60Ah
- Charging Duration: Approx. 15 hours
- Sub Battery: 11V20Ah
- Charging Duration: Approx. 4 hours
- Charging Ambient Temperature: 0 to 40°C (BMS protection program activates if battery temperature exceeds 55°C)
- Battery Management System (BMS) Protection: Over-heating, short circuit, over-current, over-discharge, and over-charge protection.
- Sub Battery Operating Voltage: 8.25V to 12.6V
Motor:
- Type: BLDC Hub Motor
- Nominal Power: 2000W*2
- Max. Power: 6000W*2
Charger:
- Input Voltage: 100-120V/200-240V~ (Main), 100-240V~ (Sub)
- Max. Output Voltage: 95.45V 4A (main battery charger), 12.6V 5A (sub battery charger)
Tires:
- Type: 13 inch wide tubeless tire
- Tire Pressure: 32 psi
- Material: Rubber
Brakes:
- Type: Hydraulic brake
- Quantity of Pistons: 4-pistons
- Electric Brake: ABS&EBSA (BMS start protection program, ABS/EBS fails if battery temperature exceeds 55°C)
Suspension:
- Type: Hydraulic spring shock
- Spring Rate: 950 ibs/in.
Display:
- Type: EY4 LCD Bluetooth Display (Ability to connect to DUALTRON APP)
- Size of LCD: 95*36mm, about 4.2 inches
Usage Features
The scooter is equipped with a multi-switch on the handlebar to control various functions.
- Turn Signal Button: Press left/right side to activate corresponding turn signal, which will blink.
- Headlight Button: Toggles the headlight on/off.
- Horn Button: Activates the horn, causing the scooter to beep.
- Ambient Light Button: Toggles both sides of the ambient light on/off.
- Warning Light Button: Activates blinking left and right signals until pressed again.
- Accelerator: Pull the throttle to increase speed.
- Bluetooth Connectivity: The EY4 LCD display supports Bluetooth connection to the DUALTRON APP. Users can scan a QR code to download the app, register, and then search for the scooter to bind it. This allows for choosing speed modes and deactivating "SAFE mode" (zero start-up feature).
- Riding: To ride, power on the scooter and select a speed mode via the Dualtron app. Stand on the footboard with one foot and push off with the other to start gliding. Ensure SAFE mode is deactivated (by squeezing the brake lever if activated). Once both feet are on the footboard, pull the throttle to accelerate. The scooter has an initial speed of 0 km/h, but the zero start-up feature can be disabled via the app, requiring the scooter to reach 1.9 mph (3 km/h) before the motor engages.
- Braking: Slow down by releasing the throttle and squeezing the brake levers. Hard braking should be done cautiously to avoid serious danger or injury.
- Turning: Shift body weight and slightly turn the handlebar. Users are advised to be mindful of road conditions and sufficient turning space.
- Folding: The scooter can be folded by releasing the handle lock, unscrewing the folding knob and M8 screws, and then folding the steering tube. It's important to reinstall the folding knob and M8 screws when unfolding.
- Carrying: If necessary, the scooter can be carried by lifting the bottom of the front fork and rear foot pedestal, ideally by two or more people, due to its weight.
Maintenance Features
- Damper Adjustment: The shock rebound resistance can be adjusted by turning the adjustment knob. Turning right increases resistance, while turning left decreases it. The factory default setting can be modified according to riding habits.
- Folding Knob and M8 Screws: These components are crucial for securing the steering tube when unfolded. The manual explicitly states that the folding knob may break and fall down if the M8 screws are not installed, emphasizing their necessity. When folding, these screws should be unscrewed, and when unfolding, they must be reinstalled.
- Handlebar Adjustment: If the handle becomes slightly shaken during use, the adjustment screw can be tightened.
- Safety Instructions: The manual advises against using an electric screwdriver for assembly to prevent damage. It also warns about the risk of pinching during folding and carrying.
- App Updates: Users are encouraged to scan a QR code to download the latest user materials, updates, and safety instructions, suggesting ongoing software and safety support.
Need help?
General
To Next Page
