Loudspeaker
Instruction
Manual
English
Bl-WIRING/Bl-AMPING
INSTRUCTIONS
Please note
that using amplifiers
with A and
B sets of speaker
Higher specification
MISSION
loudspeakers
are
equipped
with
}gL'gg1ae':ke$g'y
one set
Shomd be used
for any one
pair of
four connection terminals.
This provides
direct access
to the
high
p
frequency and low
frequency filter
networks
and associated
drive
Bl-AMPING
gnits within the lofudspeaker.h_Their
péanormancedcgn
be
enhhanced
The pedormance
of your
system can
be ‘further enhanceq
O,‘/er
Y makmg-use
° more
sop 'St'Cate
Wm-"9 an "Vmg
SC emes
that achieved
with Bl-WIRING by extending
the
same principal
made possmle
by these separate
C°nneCt'°ns'
one stage further
to include separate amplification
for
the low and
WARNING: Do
not make any connections
to
your amplifier
while
high frequency sections
of the loudspeakers.
This eliminates
the
it
is switched on and
connected
to the mains
supply.
Please distortion
caused by the
interaction of low
and high frequency
check
all connections
thoroughly
before attempting
to
re-connect
currents in the amplification
stage as well
as the loudspeaker
the mains
power supply.
Always ensure
that the
volume control
on
cables.
your
amplifier is set
to a minimum
before
switching on.
After
-
._ -
.
..
-
switching on,
select the
required input,
and gradually
increase the Zaryffmwnt
,s"1,e,,',‘§'§,°[,‘*
,§§,“'r?§urf°%heinlw'§g$sn
Wlume
Comm ‘O the required
'eVe|'
or two stereo
gmplifiers; one to drivesthe
right lougspeaker
veith the
Bl-WIRING
other driving the
left loudspeaker.
See your amplifier
instruction
- -
-
-
manual for
details on how to operate
it in the
required mono mode
B"w'r'ng
uses
‘our Conductors’
oneffm
each tenlmal’
for Bi-Amping
We recommend
that you use
identical
units to
dramatically
enhance
the performance
o your loudspea
ers.
i .
‘- -
-
- -
- -
wiring
eliminates signed
distomon
associated with
Iow and high
avoid potential
imbalances in sonic
performance
and sensitivities.
frequency
currents interacting
with
one another
within a
single
Bi-Amping additionally benefits
your system
by placing
a lower
cable, as
used in conventionally
wired
systems.
power
demand on the individual
amplifiers
at a given volume
level,
.
-
increasing
the available headroom
which will
allow higher
sound
1. Remove the
shorting links
from each of
the Red and
Black
(assure Ievelsto
be attained‘
terminal pairs on the rear
of yourloudspeakers.
p
2_
Y -H
d Ie h
f M|SS|oN
CYRUS t
1.
Remove the shorting
links from each of the
Red and
Black
ou wi nee
two ngt s o
or
wo-core
Ioudspeaker Came
per mudspeaken
terminal
pairs on the rear of your loudspeakers.
3_ C Ct
th we
f- 4 t th
fr m f mi
I 2.
You will need
two lengths of MlSSlON
or CYRUS
two-core
onne
eca
sas per
ig a e o 0
smanua
ensuring correct polarity
at all
times ie
positive (+)
'°:rd]g%%2kZg|S2?|e
and one
stereo amp|mer('n
mono mode)
connections
on the right
loudspeaker go
to‘ the positive
(+) p
p
connections on the
right channel
of the amplifier.
3. Connect your
system as_ per fig.
5 at_the front of this
_manual
4_ M
t Hf h
| -
|e t fc n
Ct f h
ensuring
correct polarity
at all times i.e. positive
(+)
os amp iers ave onyasing
se
o o ne ors or
eac
loudspeaker,
in which case the
two
wires
will
need to be joined
comegggg gr?t|q;erir'g:gu|%?§fake'
9° t°
the posmve
(+)
at the amplifier connector.
If you are
in any doubt,
ask your Co
e
9 p
dealer
to do
this for you.
To Next Page
Loading...
