How to fix unable to register error on Mitsubishi Electric Fresh Master GUF-100RDH3?
If you are unable to register your Mitsubishi Electric Air Conditioner, it may be because the Fresh Master, linked with the air conditioner, cannot be group registered except through the interlock setting with the Remote controller. To resolve this, change the setting of the SW3-1 switch and reset the registration, or register it interlocked.
What to do if the operation display on my Mitsubishi Electric Air Conditioner turns off immediately?
If the operation display on the Mitsubishi Electric Air Conditioner's remote controller appears but immediately turns off, ensure that the main power is supplied to the Fresh Master. If it is not, supply main power to resolve the issue.
What to do if my Mitsubishi Electric Fresh Master GUF-100RDH3 shows a drain error?
If your Mitsubishi Electric Air Conditioner displays a drain error, it means the drain water isn't being properly discharged. Here are a few things to check: * Ensure the unit is levelly installed. * Verify the drain pipe is installed with a gradient of more than 1/100. * Check for leaks from the permeable-film humidifier. If there is a leak, fix it or replace the permeable-film humidifier. If the problem persists after checking these items, consider replacing the PCB (printed circuit board).
Why is my Mitsubishi Electric Fresh Master GUF-100RDH3 Air Conditioner flashing HO after booting?
If the Mitsubishi Electric Air Conditioner system is booting, the HO may flash for up to 10 minutes, which is normal. If HO continues to flash for more than 10 minutes, check the following: 1. Confirm group registration has been completed. If not, conduct group registration. 2. If the Fresh Master address has been changed, conduct the group registration again. If HO continues to flash for more than 10 minutes after re-registering the group and rebooting, replace the PCB (printed circuit board).
What to do if my Mitsubishi Electric Fresh Master GUF-100RDH3 Air Conditioner displays a damper motor error?
If your Mitsubishi Electric Air Conditioner shows a damper motor error, check the following: * Ensure the CNL connector is firmly connected. * Verify the connector of the damper motor section is firmly connected. * Check if the damper operates when the damper motor is running. If not, replace the damper motor. If the problem persists after checking these items, replace the PCB (printed circuit board).
What to do if my Mitsubishi Electric Air Conditioner shows an indoor temperature sensor error?
If your Mitsubishi Electric Air Conditioner displays an indoor temperature sensor error, check the following: * Ensure the connectors of each thermistor are firmly connected. * Verify each relay connector is firmly connected. If the problem persists after checking these items, replace the PCB (printed circuit board).
What to do if my Mitsubishi Electric Fresh Master GUF-100RDH3 indicates a disconnected water sensor connector?
If your Mitsubishi Electric Air Conditioner shows a disconnected water sensor connector error, check the following: * Ensure the CN4D connector is firmly connected. If not, firmly connect the connector. * Verify the relay connector between the PCB and water sensor is firmly connected. If not, firmly connect the connector. If the problem persists after checking these items, replace the PCB (printer circuit board).
How to turn off test run on Mitsubishi Electric Fresh Master GUF-100RDH3?
To resolve the test run issue on your Mitsubishi Electric Air Conditioner, ensure that the test operation SW (SW1-1, 7, 8) is set to OFF.
What to do if my Mitsubishi Electric Air Cleaner does not run?
If your Mitsubishi Electric Air Cleaner isn't running, first ensure there isn't a power failure. After power restoration, press the [ON/OFF] button. Also, check if the power supply is turned ON and that the fuse in the power supply hasn't blown; replace it if necessary. Finally, verify that the earth leakage breaker is properly set.
Why does my Mitsubishi Electric Air Cleaner run briefly, but soon stops?
If your Mitsubishi Electric Air Cleaner runs briefly and then stops, it might be due to obstructions at the air inlet and outlet of the unit. Remove any obstacles and rerun the system. Another cause could be filters filled with dust and dirt. Clean the filters before rerunning the air cleaner.
General| Cooling Capacity | 10.0 kW |
|---|---|
| Heating Capacity | 11.2 kW |
| Refrigerant | R410A |
| Weight (Indoor Unit) | 32 kg |
| Weight (Outdoor Unit) | 98 kg |
| Indoor Unit Noise Level | 42 dB |
To Next Page
