To Next PageTo Next PageWhy does my Mitsubishi Electric PEAD-A24 make cracking noises?
The cracking or creaking sound you hear from your Mitsubishi Electric Air Conditioner can be heard when parts rub against each due to expansion and contraction from temperature changes.
What to do if an error code appears on my Mitsubishi Electric Air Conditioner remote?
If an error code appears on the remote controller display of your Mitsubishi Electric Air Conditioner, the protection devices have operated to protect the air conditioner. Turn off the power switch immediately and consult your dealer. Be sure to provide the dealer with the model name and information that appeared in the remote controller display. Do not attempt to repair this equipment by yourself.
Why is my Mitsubishi Electric Air Conditioner remote not working?
If nothing appears on your Mitsubishi Electric IR wireless remote controller display, the display is faint, or signals aren't received unless very close, the batteries are likely low. Replace the batteries and press the Reset button. If nothing appears even after replacing the batteries, make sure that the batteries are installed in the correct directions (+, –).
Why doesn't my Mitsubishi Electric PEAD-A24 blow warm air immediately when heating starts?
Warm air does not blow from the indoor unit of your Mitsubishi Electric Air Conditioner until it has sufficiently warmed up.
Why does my Mitsubishi Electric Air Conditioner stop heating before reaching the set temperature?
During heating mode, if your Mitsubishi Electric Air Conditioner stops before reaching the set room temperature, it may be because when the outdoor temperature is low and the humidity is high, frost may form on the outdoor unit. Normal operation should begin after approximately 10 minutes.
Why won't my Mitsubishi Electric PEAD-A24 turn back on immediately?
If your Mitsubishi Electric Air Conditioner doesn't restart immediately after stopping, wait approximately three minutes. Operation has stopped to protect the air conditioner.
Why does my Mitsubishi Electric PEAD-A24 Air Conditioner make a draining noise?
The draining water or motor rotation sound you hear from your Mitsubishi Electric Air Conditioner is the drain pump operating and then stopping when cooling operation stops. Wait approximately 3 minutes.
Why does the fan speed of my Mitsubishi Electric Air Conditioner change automatically?
The fan speed of your Mitsubishi Electric Air Conditioner changes automatically for the following reasons: * To avoid blowing out cold air at the beginning of heating operation, the air conditioner automatically adjusts the fan speed gradually from lower to the set speed. * It also adjusts its fan speed to protect the fan motor when return air temperature or fan speed excessively rises.
What does it mean when the operation lamp is blinking on my Mitsubishi Electric PEAD-A24 Air Conditioner?
If the operation lamp near the receiver for the IR wireless remote controller on the indoor unit of your Mitsubishi Electric Air Conditioner is blinking, the self diagnosis function has operated to protect the air conditioner. Turn off the power switch immediately and consult your dealer. Be sure to provide the dealer with the model name. Do not attempt to repair this equipment by yourself.
Why does my Mitsubishi Electric Air Conditioner make a hissing sound?
The flowing water sound or occasional hissing sound you hear from your Mitsubishi Electric Air Conditioner can be heard when refrigerant is flowing in the air conditioner or when the refrigerant flow is changing.
General| Brand | Mitsubishi Electric |
|---|---|
| Model | PEAD-A24 |
| Category | Air Conditioner |
| Language | English |
Explains safety symbols used in text and illustrations, and provides unit disposal guidelines.
Details critical safety warnings regarding unit installation, operation, and handling to prevent injury or damage.
Identifies components of the indoor unit and specific details for the PEAD-A-AA Ceiling Concealed model.
Describes the display section and operation buttons of the wired remote controller.
Details the buttons on the wireless remote controller and instructions for battery installation.
Explains how to change screens and describes the different screen types available on the remote controller.
Overview of settings for language, function limits, mode selection, and display options.
Details the standard displays for operation status, timer monitoring, and timer setup.
Illustrates the day and time display and provides instructions for setting the current time.
Detailed steps for setting the day of the week and the current time on the remote controller.
Instructions on how to turn the air conditioner unit on and off using the remote controller.
Covers selecting operation modes, setting temperature, and adjusting fan speed for optimal comfort.
Information for multi-system configurations and details on automatic cooling/heating operation.
Explains how to use the ventilation function with wired and wireless remote controllers.
Guides on setting timers using the wired remote, including weekly timer setup.
Instructions for viewing, turning off, and turning on the weekly timer settings.
Detailed steps for setting up the simple timer, including time increments and start/stop options.
Guidance on viewing, turning off, and turning on the simple timer settings.
Explains how to set the auto off timer for automatic unit shutdown after a specified period.
Instructions for checking, turning off, and turning on the auto off timer.
Details on how to lock and unlock the remote controller buttons to prevent unintended operation.
Provides information on how to interpret and respond to error codes displayed by the unit.
Introduction to the remote controller function selection mode for customizing unit behavior.
Covers function selection flowchart, language, operation limits, mode settings, and display options.
Specific procedures for setting language, function limits, mode selection, and display preferences.
A table illustrating display options for various functions across multiple languages.
Details on setting room temperature and auto cooling/heating display in different languages.
Instructions for operating the unit using the wireless remote receiver in case of remote failure.
Step-by-step guide for cleaning and removing air filters, including important cautions.
Addresses common operational problems like poor cooling/heating, unusual sounds, and display errors.
Troubleshooting steps for excessive noise and problems with the wireless remote controller's display or signal.
Guidance on what to do when the operation lamp near the wireless remote receiver on the indoor unit is flashing.
Provides detailed technical specifications for the PEAD-A-AA series air conditioner models.
