Why only motion areas are displayed on Mitsubishi Lcd projector?
If only the motion areas in the images supplied from the computer aren’t displayed on your Mitsubishi Lcd projector, this is caused by the computer being used. Contact the manufacturer of your computer.
Why does Mitsubishi HC6500 power turns off?
Your Mitsubishi Lcd projector might be turning off because the intake vent and/or exhaust vents are blocked. Remove any obstructions, wait for the fan to stop (until the STATUS indicator goes out), unplug the power cord, wait at least 10 minutes, plug it back in, and press the POWER button. If the STATUS indicator is steady red, the lamp needs replacing. Check that AUTO POWER OFF is set to OFF. It's also possible the lamp is deteriorating and may go out after a while.
What to do if Mitsubishi HC6500 Lcd projector says 'no signal'?
If your Mitsubishi Lcd projector displays “NO SIGNAL”, first turn on the connected device and ensure it is functioning correctly. Verify the external device is outputting signals, especially if it’s a notebook computer. Check the cable connecting the projector to the external device for any defects, and ensure the projector is connected using the correct terminals. Confirm that the connected device is correctly selected as the input source. If using an extension cord, replace it with the supplied cable to check if images are projected correctly; if they are, use an RGB signal amplifier with the extension cord.
How to fix shaking images on Mitsubishi HC6500 Lcd projector?
To fix shaking or displaced images on your Mitsubishi Lcd projector, first check that the cable connected to the external device isn’t intermittent and connect the cable’s plug firmly. Then, press the AUTO POSITION button. If the issue persists, it may be due to the computer outputting out-of-spec signals; in this case, adjust the SIGNAL menu settings.
How to fix distorted images on Mitsubishi HC6500 Lcd projector?
To correct distorted images on your Mitsubishi Lcd projector, adjust the projector and the screen so that they are perpendicular to each other.
What to do if Mitsubishi HC6500 Lcd projector power can not be turned on?
If your Mitsubishi Lcd projector won't power on, first, connect the power cord to the projector and plug it into a wall outlet. Ensure no objects are blocking the air inlet or outlet grill; if there are, remove them, unplug the power cord, let the projector cool, then plug the cord back in and press the POWER button. Also, don’t expose the air outlet grilles to heat. Check if the filter is clogged with dirt or dust, and clean it if necessary. After the STATUS indicator stops blinking, press the POWER button. Note that the lamp can’t turn on again for one minute after it goes out, or if you unplug the power cord while the fan is rotating. Press the POWER button several times. If the lamp is at the end of its life, replace it. Ensure the lamp cover is attached. If none of these steps work, u...
What to do if Mitsubishi HC6500 Lcd projector remote control doesn’t function?
If the remote control for your Mitsubishi Lcd projector doesn’t function easily or at all, check that the batteries are loaded correctly and are not weak. Ensure the remote control sensor isn’t exposed to direct sunlight or fluorescent light. Use the remote control within its operation range and at least 10 cm away from the projector.
What to do if Mitsubishi HC6500 buttons don’t function?
If the buttons on the control panel of your Mitsubishi Lcd projector (except for the POWER button) don’t function, PASSWORD FUNCTION in the FEATURE menu has been set to MENU ACCESS to enable the password lock. Cancel the password lock or contact the person in charge of management of the projector.
Why does Mitsubishi HC6500 show different color tint?
If your Mitsubishi Lcd projector displays a different color tint, when comparing images projected by two projectors, tints in the displayed images may be different because of variation between their optical components. This is not a malfunction. When comparing the image projected by this projector with those displayed on the television or PC monitor, tints in the displayed images may be different because of difference in the range of color reproducibility. This is not a malfunction.
How to remove fine streaks on Mitsubishi HC6500 images?
Fine streaks on projected images from your Mitsubishi Lcd projector are due to interference with the screen surface and are not a malfunction. Try replacing the screen or slightly displacing the focus. Vertical or horizontal streak noise may appear depending on the DVD player or game console you use; you can reduce this by enabling the LPF.
General| Brand | Mitsubishi |
|---|---|
| Model | HC6500 |
| Category | Lcd projector |
| Language | English |
To Next Page