PBV20N2 PBV20N2 Service Service ManualManual
CODE
CODE TRUCKTOOL TRUCKTOOL AND AND DISPLAY DISPLAY DESCRIPTIONDESCRIPTION
185185 Height sensor mismatchHeight sensor mismatch
HT SENS.MISMHT SENS.MISM
(Alarm) Stored(Alarm) Stored
If the truck is not If the truck is not equipped with side stabilizers, check that the parameter INITIAL LIFT is equipped with side stabilizers, check that the parameter INITIAL LIFT is notnot
set to 2.set to 2.
If the truck is equipped If the truck is equipped with side stabilizers:with side stabilizers:
•
• Check the wiring of the height Check the wiring of the height sensor.sensor.
•• Disconnect the height sensor and test the redundant Disconnect the height sensor and test the redundant switches. If the states are not equal,switches. If the states are not equal,
test if the switch works by moving a magnet in test if the switch works by moving a magnet in front of it.front of it.
•
•
Check that the magnet counterpart (attached to the lifting Check that the magnet counterpart (attached to the lifting carriage) is intact.carriage) is intact.
•
•
Check the wiring of the encoder card (extra Check the wiring of the encoder card (extra I/O).I/O).
If the problem persists, replace the height If the problem persists, replace the height sensor.sensor.
186186 Motor temperature notificationMotor temperature notification
WARN. MOT.TEMPWARN. MOT.TEMP
(Warning)(Warning)
This is only a notification. This is only a notification. To limit further heat generation, To limit further heat generation, the parameter cutback starts whenthe parameter cutback starts when
the motor temperature reaches 120the motor temperature reaches 120˚C. The truck can be used normally.˚C. The truck can be used normally.
187187 Controller temperature notificationController temperature notification
WARN. TWARN. TH.PROTECH.PROTECTT
(Warning)(Warning)
This is only a notification. This is only a notification. To limit further heat generation, To limit further heat generation, the parameter cutback starts whenthe parameter cutback starts when
the controller temperature reaches 75the controller temperature reaches 75˚C. The truck can be used normally.˚C. The truck can be used normally.
188188
Load sensor value is out of rangeLoad sensor value is out of range
LOAD.SEN.OUT RNGLOAD.SEN.OUT RNG
(Warning) Stored(Warning) Stored
This warning indicates a pressure sensor problem. Either the pressure sensor’s voltage is notThis warning indicates a pressure sensor problem. Either the pressure sensor’s voltage is not
within the calibrated value range within the calibrated value range or it exceeds the calibrated values too or it exceeds the calibrated values too much.much.
189189 Battery lock not closedBattery lock not closed
BATTERY LOCKBATTERY LOCK
(Alarm)(Alarm)
This alarm indicates that the battery lock is This alarm indicates that the battery lock is not closed.not closed.
In such a case, check the battery lock state In such a case, check the battery lock state from the tester menu. If the from the tester menu. If the lock is stated to belock is stated to be
open while the battery is open while the battery is mechanically locked, check the battery lock sensor operation andmechanically locked, check the battery lock sensor operation and
wiring.wiring.
190190
Motor braking errorMotor braking error
BRK TIMEOUTBRK TIMEOUT
(Alarm) Stored(Alarm) Stored
One possible cause for this alarm is too One possible cause for this alarm is too steep braking ramp (parameter). Try to lower thesteep braking ramp (parameter). Try to lower the
braking ramps from the parameters. Also braking at a slope braking ramps from the parameters. Also braking at a slope when the truck is loaded canwhen the truck is loaded can
cause this error.cause this error.
192192
Waiting for EPSWaiting for EPS
EPS RELAY OPENEPS RELAY OPEN
(Alarm) Stored(Alarm) Stored
This alarm indicates that there is some problem in This alarm indicates that there is some problem in the steering and the the steering and the steering has frozen.steering has frozen.
To Next Page
Loading...
