MIVARDI MCA - Page 6

6 | MIVARDI
EN / BITE ALARM
1. Bite alarm
Turn on the alarm by moving the
main two -position switch to the
right (lever switch located at the
bottom of the alarm). When the
alarm is on, all the lights will flash
2x and beep 2x.
Slide the switch to the left to turn off
the alarm.
2. Nightlight
Press the Vbutton 2 seconds to turn
on or off the night lights.The night-
light colour is white.
3. Volume
The volume is controlled using the
„V“ (volume) button. A total of 8
levels are available. The last, 8th
level serves as silent mode and is
therefore without sound.
4. Tone
The tone level is regulated by the
„T“ (tone) button. There are 8 tones
levels available from lowest to
highest.
5. Sensitivity
The degree of sensitivity is set with
the „S“ button. There are 8 levels of
sensitivity.
The alarm uses a rotating wheel
with four magnets to detect very
short movement. When setting the
highest level of sensitivity (level 8),
the detector detects amovement of
approx. 2.5– 3 mm.
6. Color selection
The „AT“ button is available to set
the colour of the LEDs. Bite alarm
has 6 colours available: red / green
/ blue / yellow / purple / white. The
bite indication diode (left) and the
memory diode (right) always have
the same colour. Ashort press of the
„AT“ button will change the colour
red g green g blue g yellow g
purple g white g red…
7. Intelligent Anti -theft alarm
1st long pressing (2sec) of the „AT“
button = Anti -theft alarm is ON, this
is indicated by one short beep.
2nd long pressing (2sec) of the „AT“
button= Anti -theft alarm is OFF, this
is indicated by 2 short beeps.
If the rod is removed from the alarm,
the anti -theft function will activate
after 1 second on the bite alarm and
receiver, emitting afast beep sound
for 5 seconds. If arod lift is detected
within 30 seconds, the anti -theft
function will not be activated.
The function will be active if the rod
is not removed from the alarm for 30
seconds after the anti -theft alarm
function is activated.
8. Working mode
Bite indication (front) is running =
left diode and right diode light up
at the same time, when running is
stopped, the right diode (memory)
lights up for 20 seconds, the left
diode (running indication) is unre-
sponsive.
Bite indication (back) is running
= left diode and right diode flash
simultaneously, when running stops,
the right diode (memory) flashes for
20 seconds, the left diode (operation
indication) does not react.
Illuminated line roller is anight light
only, does not indicate engagement.
The alarm should emit aquick short
beep when the fish is in afast bite.
The swingers LED will sync with the
right LED (memory LED).
9. Low battery warning
If the low battery level is detected
(Low electric voltage value is
6.7 V,The low battery level means
the bite alarm can continue working
for about 8 -10hours), then one long
beep (0.5sec) is provided every 15
minutes.
The memory LED lights for 10sec
after this beep. On the receiver the
correct LED lights for 10sec (the LED
that belong to the bite alarm with
low battery detected)
RECEIVER
1. Receiver
Turn on the receiver by long pressing
the first button (3 seconds). Vibration is
off, one short beep will sound to indicate
the receiver is on.
Another long press (3 seconds) of the
button will cause the receiver to turn off,
adouble beep will sound to indicate that
the receiver is off.
For the best performance
of the receiver we recommend:
• To place the receiver as high as
possible above the ground.
• Do not put the receiver together
with other electrical products in your
pockets.
• Place the receiver on the outside of
your clothing if you are wearing it.
• Make sure there are good quality
and charged batteries in the product.
• Ensure that the space between the
receiver and alarms is as clean as
possible so that there is no loss of
signal.
2. Vibration
Along press of the minus „-“ button
will turn on the vibration function, one
short beep will be heard. When you
press the button again for along time,
the vibration will turn off and a short
beep will sound.
3. Volume steps
There will be two volume buttons on
the receiver (“+” and “-”) to adjust the
volume, There will be 8 volume steps in
total 8 volume steps. Position 0 means
silent mode. Positions 1 - 7 mean the
volume steps. (same as the bite alarm).
4. Tone steps
The tone of the receiver will be automa-
tically synchronised with the bite alarm,
different alarms can have different tones.
5. Learning code / Pairing
There will be six fixed colours LED: red,
green, blue, yellow, white, purple (from
the left LED to the right LED).