Mod Wave - Table of Contents

To Next Page

To Previous Page

TABLE OF CONTENTS

Safety ……..………..........................................................................................................................................3

Soldering Tips…..………....................................................................................................................................4

Wiring Tips …...……........................................................................................................................................5

Hardware Fastening Tip……………................................................................................................................ 6

Step by Step Assembly

Section 1 – Mounting of Top Components

Section 2 – Mounting of Rear Components

…….............................................................................6

…….............................................................................9

Section 3 – Mounting of Front Components ……...........................................................................10

Section 4 – Making Wire Connections …..……...........................................................................11

Section 5 – Mounting Electronic Components ...........................................................................16

Section 6 – Assemble and Fasten the Cover Plate ......................................................................18

Section 7 – Make and Connect the RCA Cables .........................................................................19

Section 8 – Finishing Up …………………….............................................................................20

Step 1 – File the chassis holes (p. 6)

Step 2 – Mount the rubber grommets (p. 7)

Step 3 – Mount the 9 pin miniature tube sockets and shields (p. 7)

Step 4 – Mount the tank in & out phono jacks (p. 8)

Step 5 – Mount the output transformer “TR2" (p. 8)

Step 6 – Mount the power transformer “TR1” (p. 8)

Step 7 – Mount the terminal strips (p. 8)

Step 8 – Mount the remaining top surface locking lugs (p. 8)

Step 9 – Mount the reverb tank (p. 9)

Step 1 – Mount the power cord receptacle (p. 9)

Step 2 – Mount the fuse holder (p. 9)

Step 3 – Mount the phono in and out jacks (p. 9)

Step 4 – Mount the footswitch jack (p. 10)

Step 1 – Mount the lamp holder (p. 10)

Step 2 – Mount the power switch (p. 10)

Step 3 – Mount the output jack (p. 10)

Step 4 – Mount the reverb on/off switch (p. 10)

Step 5 – Mount the 500K reverb and 10K dwell pots (p. 10)

Step 6 – Mount the input jack (p. 10)

Step 1 – Connect the output transformer (TR2) wires (p. 11)

Step 2 – Connect the power transformer (TR1) wires (p. 11)

Step 3 – Connect the power switch (p. 11)

Step 4 – Connect the power cord receptacle (p. 11)

Step 5 – Connect the filaments (p. 12)

Step 6 – Connect the power supply wires (p. 12)

Step 7 – Connect the reverb driver wires and components (p. 13)

Step 8 – Wire the phono jacks (p. 13)

Step 9 – Wire the front panel components (p. 14)

Step 10 – Prepare and connect the shielded wires (p. 14)

Step 11 – Connect the remaining tube socket wires (p. 16)

Step 1 – Connect the diodes (p. 16)

Step 2 – Connect the filter caps and resistors (p. 17)

Step 3 – Connect the “phono in” components (p. 17)

Step 4 – Connect the V1 components (p. 17)

Step 5 – Connect the V3 components (p. 17)

Step 6 – Connect the V4 components (p. 18)

Step 1 – Mount the rubber feet (p. 18) Step 2 – Mount the cover plate (p. 18)

Step 1 – Make the 12" output cable (p. 19) Step 2 – Make the 14 ½” input cable (p. 19)

Step 3 – Connect the cables to their respective phono jacks (p. 20)

ASSEMBLY DRAWINGS

PARTS LIST DRAWINGS & Tool List

…….…………………………….separate document (7 drawings)

…...….separate document (3 pages, Tool List on p. 3)

Main Page