This document provides comprehensive information for the installation, use, and maintenance of a Mode Bathrooms Shower Cabin, specifically the Rectangular Shower Cabin with product code S120WWVR/S120BLR.
Function Description
The Mode Bathrooms Shower Cabin is a self-contained shower unit designed for personal hygiene. It features a shower tray, back panels with integrated shower components (including a hand shower, shelf, and multiple body jets), fixed glass panels, and sliding doors. The cabin is designed to provide a complete showering experience within a dedicated enclosure, offering both overhead and handheld showering options, along with the added luxury of body jets. The unit is designed for domestic use and requires connection to both hot and cold water supplies.
Important Technical Specifications
Product Name: Rectangular Shower Cabin
Product Code: S120WWVR/S120BLR
Water Pressure Requirement: This product requires a minimum of 2 bar water pressure to operate effectively. It does not exceed a maximum of 4 bar pressure, as this will cause damage to the unit and invalidate the product warranty.
Material Composition: The shower cabin is made of aluminium, which undergoes extrusion, fabrication, polishing, and anodising processes. The glass components are described as "toughened glass."
Dimensions (implied from parts list): The assembly involves various components of specific sizes, such as 1xShower roof (A), 1xBack panel left side (B), 1xBack panel right side (C), 1xTray (D), 1xFixed glass (E), 1xSliding glass (F), 2xSelf adhesive rubber seal (G), 1xGlass seal (H), 2xDearation rubber seal (I), 1xVertical profile (J), 1xRubber seal between the fixed glass (K), 2xRubber seal on the fixed glass/sliding glass (L), 1xWood floor (optional) (M), 1xTop shower (N), 1xHand shower (O), 1xHolder (P), 1xFlexible hose (Q), 1xFlexible hose connector (R), 1xGlass shelf (S), 2xGlass clamp and screw cap (T), 1xRubber seal (U), 2xTop rollers and washers (V), 2xBottom rollers and washers (W), 10xM4x16 (2 spare) (X), 8xM4x16 (2 spare) (Y), 6xM4x22 (Z), 22xST4x16 (2 spare) (AA), 5xST4x55 (1 spare) (BB), 3xST4x12 (1 spare) (CC), 3xTube clips (1 spare) (DD), 2xElbow joint (EE), 2xWhite rubber seal (FF), 6xHexagon screw (1 spare) (GG), 1xSmall black rubber seal (HH), 1xBig black rubber seal (II), 2xST4x35 (1 spare) (JJ), 10xST4x10 (2 spare) (KK), 1xFixed glass (LL), 1xVertical profile (MM), 1xCorner profile (NN).
Performance Characteristics (from CE marking):
- Cleanability: Pass (Clause 6.2 of BS EN 14428:2015)
- Impact resistance/shatter properties: Pass (Clause 6.3 of BS EN 14428:2015)
- Durability: Pass (Clause 6.4 of BS EN 14428:2015)
DOP No: ENC2001140GZ64E1
Usage Features
Installation Requirements:
- Competent Plumber: Installation should be carried out by a competent plumber.
- Tools Required: Tape measure, spirit level, pencil, Ø3mm drill bit, spanner, drill, cross head screwdriver, rubber mallet, silicone sealant, and Forfex (scissors).
- Heavy Product: This product is heavy and requires two people for installation.
- Shower Tray Feet Adjustment: The shower tray feet must be adjusted to level the tray in the desired location before fitting the shower cabin.
- Shower Waste: Shower waste is not supplied and must be acquired separately.
- Water Supply Connection: Ensure correct hot and cold water feed connections to the cabin shower valve. All nuts and washers must be tight and secure.
- Leak Test: After completing assembly, turn on water supply and fully test the product for leaks before moving the cabin into its final position.
Adjusting Sliding Doors:
- The sliding doors can be adjusted to be parallel by turning the screw underneath each top roller either clockwise or anti-clockwise.
- To adjust the bottom rollers, lift or lower each corner.
- Caution: Take care not to over-tighten the roller screws, as this will cause the rollers to malfunction.
Maintenance Features
Care Instructions (After Care):
- Regularly clean your shower product with warm soapy water to prevent lime scale build-up.
- Do not use abrasive cleaning fluids or materials, or strong chemical cleaners, as this will damage the product surface.
Maintenance Instructions:
- Clean the plastic parts with a cloth and mild detergent.
- Never use any abrasive creams, dissolvents, acetone, or detergents and disinfectants that contain chlorine.
- The supplier accepts no liability for any type of use of care other than those contained in these instructions.
- The supplier reserves the right to introduce technical changes without notice.
General Information and Warranty:
- Damage Reporting: Please inspect the product upon delivery. Any missing parts or manufacturing defects must be reported immediately to the supplier. Damage or defects reported later will not be accepted.
- Handling Glass Parts: Take care when handling glass parts. Avoid heavy contact between the glass edges and any hard surface. Glass breakage claims will not be accepted after the product has been unpacked.
- Aluminium Care: Aluminium is a soft metal, and undergoes a series of extrusion, fabrication, polishing, and anodising processes to create the finished shower cabin. Some light surface marks are normal and are a result of the manufacturing processes. Quality control ensures that this item is of a good standard and is fit for purpose.
- Product Warranty: This product requires a minimum of 2 bar water pressure to operate effectively. Do not exceed a maximum of 4 bar pressure, as this will cause damage to the unit and invalidate the product warranty.
- Packaging Disposal: The packaging is 100% recyclable and should be disposed of in a safe and environmentally friendly way, preferably at a local landfill site or designated bins.
Customer Support:
- Customer help line number: 0344 804 48 48
Need help?
General
To Next Page