What does HIGH / LOW mean on Mold-Masters Laboratory Equipment?
If your Mold-Masters Laboratory Equipment displays HIGH / LOW, the waterflow sensor has detected a high or low flow rate. The coolant water system should be checked for blockages and leaks to ensure that overheating does not occur. Note: Waterflow is a monitored condition only, and these messages will not cause a pause or shutdown of the system.
What causes an OVER error on Mold-Masters TempMaster M3 Laboratory Equipment?
If your Mold-Masters Laboratory Equipment shows OVER, the RTD zone has detected a temperature above 99°C. Check that a different RTD has not been fitted.
What does the NONE error mean on Mold-Masters TempMaster M3 Laboratory Equipment?
If your Mold-Masters Laboratory Equipment displays NONE, the console has detected a control card that has no settings. This error message may be seen briefly during switch on, but it should disappear after the initial card scan. If the message persists then you may need to reapply the correct card settings.
What does CN/Z error mean on Mold-Masters TempMaster M3?
If your Mold-Masters Laboratory Equipment displays CN/Z, the console has detected a control card, but the card cannot communicate with the console. If all zones show CN/Z and no cards show / flash their SCAN LEDs, check the communication lead between the console and the controller cabinet. If only one or two zones show CN/Z, check the card for faults.
What to do if Mold-Masters TempMaster M3 Laboratory Equipment displays RTD error?
If your Mold-Masters Laboratory Equipment displays RTD, the RTD monitor cannot see an input (RTD is open circuit). Check the RTD and its wiring for a broken connection.
General| Brand | Mold-Masters |
|---|---|
| Model | TempMaster M3 Series |
| Category | Laboratory Equipment |
| Language | English |
Describes the M3 controller's purpose and intended application in hot runner plastic molding.
Lists units of measure and their conversion values for system parameters.
Provides contact information for Mold-Masters global and regional offices.
Details common safety hazards associated with injection molding equipment.
Outlines potential hazards during the operation of the equipment.
Explains typical safety symbols used for warnings and cautions.
Covers procedures for safely de-energizing equipment during maintenance.
Lists the general technical specifications of the M3 controller and console.
Explains the user interface layout and navigation elements of the controller.
Details the functions and uses of the main display screen.
Describes the different operational modes like Run, Standby, Startup, and Shutdown.
Guides the user through the process of creating a new tool configuration.
Explains how to configure detected control cards and set zone types.
Details how to adjust tool and system parameters for optimal performance.
Provides instructions on setting or changing the temperature for individual or multiple zones.
Explains the setup and operation of the melt leakage detection system.
Step-by-step guide on powering up the M3 controller.
Covers the procedures for logging into and out of the controller system.
Details the various control modes available for managing all zones.
Describes methods for saving tool configurations, either overwriting or as a new tool.
Instructions on how to load a tool configuration from local storage.
Explains how to back up tool settings to an external storage device.
Describes the user access screen and its functionalities.
Details how to manage user access levels and permissions for functions.
Provides instructions for setting up wired and wireless network connections.
Covers the procedure for upgrading the controller's software.
Guides the user through the process of calibrating the touchscreen.
Details how to perform and interpret various diagnostic tests on the controller.
Explains how to understand the outcomes of diagnostic tests.
Explains the meaning of LED indicators on controller cards for diagnostics.
Lists and explains system warning messages indicating abnormal conditions.
Provides a comprehensive list of error messages, their causes, and actions.
Covers wiring configurations for three-phase power supply options.
Details how to connect the Star/Delta option in the cabinet.
Describes the functions enabled by the USB port.
Covers the configuration of the built-in Quad IO card parameters.
Lists and describes the available input options for the Quad IO card.
Lists and describes the available output options for the Quad IO card.
Explains how to enable remote tool loading using the IO5 card.
To Next Page