Moog Source - Page 2

SPECIFICATIONS
KEYBOARD
Description: 37 Note C to C, Low note priority
Keyboard Transpose: +1 Octave (Left hand control)
Glide Time: Linear, continuously variable from less than
2 msec to 5 sec (bottom to top of keyboard)
MODULATION
Rate: Continuously variable from 0.25Hz to 325Hz
Amount (Square wave): Oscillator, zero to 16 semitones
Filter, zero to 5 octaves
OSC 1 AND OSC 2
Reference frequency: Low C 32'. 32.7Hz +/- 0.1Hz
Scale factor accuracy: 0.21% from 65Hz to 1.5kHz
Range drift due to temp: 0°C to 40°C less than
0.02%/°C
Pulse duty cycle: Continuously variable from 5% to 95%
Octave accuracy: 0.2%
Output level range: 80dB
Interval range: 2.1 Octaves
Interval cal range: ♦ /• 3%
VCF
Type: Low pass 24dB/octave cutoff slope with variable
height resonant peak at cutoff frequency.
Range of cutoff: 30Hz to 25kHz
Keyboard tracking accuracy: Full mode. .05% (30Hz to
20kHz)
Sweep of cutoff frequency by contour generator: 10 octaves
CONTOUR GENERATORS
Type: Microprocessor controlled ADSR, retnggorablu
Range of attack, decay, release times: 1 msec to 10 sec.
Range of sustain level: 0 to 100% of peak contour
VCA
Audio output level: OdBm
Dynamic range: 80dB
Output offset: Less than 100MV
REAR PANEL I/O
Fine tune: +/- 3 semitones
KB CV IN/OUT: 1 V/oclave ♦ /- 2%
Input impedance - 50K ohm
Output impedance ■ IK ohm
S-Trigger in: Switch closure to ground triggors contour
generators, input impedance greater than
IK ohm
S-Trigger out: Trigger on is switch closure to ground
Cassette I/O: Tape interface with transport on/off control
Audio Output: OdBm. Output impedance - 600 ohms
POWER REQUIREMENTS
Operating voltage range
Domestic: 95 to 130 VAC 60Hz
Export: 200 to 260 VAC 50Hz
Power consumption: Less than 30 watts
DIMENSIONS AND WEIGHT
Overall size: 26-3/8" wide, 12-1/2" deep. 3" high
(67cm x 31.75cm x 7.62cm)
Net weight: 22 lbs. (48.51kg)
WARNING
Hazardous voltages are present in power sup¬
ply circuit. Disconnect AC supply cord prior
to disassembly. Exercise care when making
tuning adjustments with unit operating to
avoid contact with exposed wiring near pri¬
mary switch and fuse holder.
Carefully r
board mounting
Lower base, rerr
left side. Use a s
up housing to g£
Increments
screws located u
remove knob fo
CAUTION
Digital Memory circuits are powered by a 3V
lithium battery, BT-1. DO NOT short circuit,
overload or attempt to charge this cell. Ex¬
plosion and release of corrosive chemicals
may result.
Power Sup
screws at front £
plate at rear, wh
housing. Power
removed withou
Digital andi
by plastic clips,
clips to avoid br
required.
DISASSEMBLY PROCEDURE
NOTE
Before proceding with disassembly, take care
to protect finished wood and lacquered metal
parts from sharp objects. Use carpeted or
similarly protected surface.
To gain access to tuning adjustments, bottom
assembly including keyboard must be separated from
upper housing. Start by removing (2) screws from
lower rear panel located on either side of Moog logo.
Place unit upside down and remove (4) screws
holding bottom to wood ends. Remove rear key¬
board mounting screws near center of bottom and
loosen (3) front keyboard machine screws until they
are finger tight.
Place unit on its feet, lift rear edge approxi¬
mately one inch and tilt forward to release housing
from front groove.
Slide housing forward to clear keys. Lift and
rotate front of housing up and rest on rear panel. Take
care not to stress flexible "tails" on membrane switch
which connect this panel to a P.C. Board at rear of
unit.
ror
«»' D«*IO
Ml 3 P
PI?
><••*., 3P
PI3
Mm*., 10
P14 H.«k«. 10
PIS
Mm*.. 10
PI#
M.a*.,8P
Ul
1C. Vo*i»(t
U?
1C. Opout*
UJ
U4
Ql TroWita,
0? Ttaorttoi.
03 IrUHillOl.
04 Turn* to*.
cm Do*. Rk«
CR2 Do*. Rk
CH3 Do*. Rk*
CR4 Oo*. Rk*
CRB
Oo*. Z**
CR# Oo*. Rk*
CR7 Oo*.Rk*
CR8 Oo*. Rk*
CR9 Oo*. Rk*
CRIO Do*. Rk
CRII Do*. Rk*
CRI?
Do*. Rk*
CRI3
Do*. Rk*
Cl <** 010 ..
C?
Ck-<mo..1
C3 C •0*010'.
C4
C4WO10..I
C6
C*P*oto».
ce Ckhoioc.1
C7 Ck*co.. F
C8 <**010., 1
C9 <**010.. 1
CIO <**010..
Cll
<**010.1
CI2
<*MOlO>.l
CIS
<**OIO>.
R4 Rkiiioi. Tr
RI4
Rttuto*. Tr