2 STEREO OUTPUT
W
W
W
W
V
Hz
dB/Oct
Hz
dB/Oct
A
mm
Stereo power RMS @4ohm
Stereo power RMS @2ohm
Bridge power RMS @4ohm
Bridge power RMS @2ohm
Input sensitivity range
High pass filter range (switchable)
High pass filter slope
Low pass filter range (switchable)
Low pass filter slope
Band pass filter
Internal fuse
Dimensions
AS 100.2
2 x 100
2 x 160
1 x 320
1 x 500
0.2 ÷ 5
20 ÷ 175
12
50 ÷ 300
12
Available
40
215 x 200 x 50
AS 200.2
2 x 200
2 x 320
1 x 640
1 x 1000
0.2 ÷ 5
20 ÷ 175
12
50 ÷ 300
12
Available
80
350 x 200 x 50
AS 300.2
2 x 300
2 x 550
1 x 1100
1 x 1800
0.2÷5
20 ÷ 175
12
50 ÷ 300
12
Available
150
590 x 200 x 50
AS 100.4
4 x 100
4 x 155
2 x 310
2 x 480
0.2 ÷ 5
20÷175
12
50÷300
12
Available
80
350 x 200 x 50
AS 200.4
4 x 200
4 x 320
2 x 640
2 x 950
0.2 ÷ 5
20 ÷ 175
12
50 ÷ 300
12
Available
150
590 x 200 x 50
OWNER’S MANUAL
WARRANTY CARD
WARNINGS
AUDIO SYSTEM AS SERIES
MOSCONI reserves the right to modify or improve the products described here without notice. The availability of the displayed
products mayvary.Products describedin thisMANUAL are a portion of all MOSCONI products. Alltrademarks mentionedare used
for descriptive purposes and all rights are reserved by their respective owners. The total or partial reproduction of this MANUAL is
prohibited.
Ch 1
Ch 2
2CH AMPLIFIER - 1 STEREO SIGNAL 2CH AMPLIFIER - 1 MONO SIGNAL
Ch 1
Ch 2
The Ch2 RCA may be
used as a by-pass
of the Ch1 RCA
DO NOT USE THIS SWITCH for this configuration
USE THIS SWITCH for this configuration
Ch 1
Ch 2
4CH AMPLIFIER - 2 STEREO SIGNAL
Ch 3
Ch 4
CONNECTING INPUT
CONNECTING SPEAKERS
Ch 1
Ch 2
Ch 3
Ch 4
Ch 1
Ch 2
Ch 3
Ch 4
4CH AMPLIFIER - 1 STEREO + 1 MONOSIGNAL SIGNAL 4CH AMPLIFIER - 1 STEREO SIGNAL
The Ch4 RCA may be
used as a by-pass
of the Ch3 RCA
The Ch3 e Ch4 RCA
may be used as a
by-pass of Ch1 and Ch2 RCA
respectively
1 STEREO OUTPUT + 1 MONO BRIDGED OUTPUT 2 MONO BRIDGED OUTPUT
HIGH PASS FILTER
FILTER SELECTION
LOW PASS FILTER BAND PASS FILTER
REMOVING GRIDS
GRIDS AND COVERS
MOUNTING GRIDS USING THE COVERS
WARRANTY
WARRANTYCONDITIONS
COMPLETE ALL SECTIONSAND RETURNTHIS DOCUMENTALONG WITH A) THE
PRODUCT TO REPAIRAND B)THE ORIGINALDATED PURCHASE RECEIPT
MOS extends a warranty to MOSCONI products for 24 months from the date of the original purchase as
declared in the appropriate box and in the original purchase receipt. Enclose the dated purchase receipt
when sending the product forreturn orrepair to the authorized dealer.
The serial number of thiscertificate mustcorrespond to the one stampedon thereturned product.
MOS is not responsible fordamages orinjury caused by improper installationor operationof theproduct.
Name
Address
e-mail & Phone
Client Autorized Dealer
Model
Serial Number
Product
MINIMUM CAPABILITY IMPEDANCE: 1OHM IN STEREO MODE; 2OHM IN BRIDGE MODE
WARNING!CAUTION:
IN CASE OF TROUBLE IMMEDIATELY DISCONTINUE
USE. Failure to comply may cause injury or damage the
product. For repair please contact an authorized
MOSCONI dealer.
DO NOT DISASSEMBLE OR MODIFY THE PRODUCT:
This action may result in accidents, fire or electric shock.
Any alteration or modification to the product immediately
voids any expressed or impliedwarranty.
THE INSTALLATION AND CONNECTION OF THE
PRODUCT SHOULD BE PERFORMED BY QUALIFIED
PERSONNEL. The installation and connection of the
product require specific technical background and
experience. . For safety reasons, always contact an
authorized dealer to install theproduct ina correct way.
DO NOTINSTALLIN AREASPARTICULARY HUMID OR
DUSTY. Avoid installing the product in areas excessively
humid or dusty. Presence of humidity or dust inside the
product can cause malfunction.
DO NOT INSTALL NEXT TO HEAT SENSITIVE
SURFACES. The amplifier may reach temperatures in
excess of 80°C (176°F) and contact with heat sensitive
surfaces may cause a fire hazard and damage to the
surface.
WHILE DRILLING HOLES, DO NOT DAMAGE TUBING
AND CABLES. While drilling holes in your vehicle during
installation, pay close attention to avoid damaging,
blocking or contact with: tubing, the fuellines, thefuel tank
and electrical cables. Failure to follow these precautions
will pose a fire hazardand damages.
DO NOT OBSTRUCT VENTS OR HEAT SINKING
PANELS. Blocking vents or heat sinking panels may
cause increased temperatures inside the amplifier. This
may cause a fire hazard.
USE THIS PRODUCT EXCLUSIVELY IN VEHICLES
WITH 12V POWER. Using the product with electrical
power other than 12V may cause fires, electric shock or
other accidents.
DISCONNECT THE NEGATIVE (GROUND) BATTERY
LEAD BEFORE CONNECTING THE PRODUCT. Failure
to do so may cause electric shock or other damage and
injury due to short circuit.
ENSURE PROPER CONNECTIONS. To avoid fire
hazard and damage to the product, use cables of proper
gauge and pay close attention to the polarity of the
connections.
AVOID TANGLING THE CABLES TO VEHICLE PARTS.
Make proper connections by following the instructions so
that the cables do not interfere with proper vehicle
operation. Cables that tangle with steering components,
gear lever, brake pedals,etc maybe dangerous.
LAY OUT THE CABLES TO ENSURE THAT THEY ARE
NOT BENT OR COMPRESSED BY SHARP METAL
EDGES. To avoid damagingor bendingthe cables,lay out
the cables far from moving parts (such as the seat rails)
and from sharp or pointy vehicle parts. If the cables are to
pass through a hole in a metal sheet, use a rubber ring to
ensure that the cable insulation won't be cut by any sharp
edge.
TO ESTABLISH A GROUND CONNECTION DO NOT
USE BOLTS THAT BELONG TO THE STEERING OR
BRAKING SYSTEM. NEVER use bolts from the steering
or braking system (or any other safety system) or the fuel
tank toestablish aground connection. Using any of these
parts may impair your ability to control the vehicle and
cause accidents, fire or otherdamage.
USE FUSES WITH ADEQUATE AMP RATING.
Otherwise there may be firesor electricshock.
USE THE CORRECT ACCESSORY PARTS AND
FOLLOW THE INSTALLATION INSTRUCTIONS. Be
sure to use only specified accessory parts. Using other
components may damage the product or result in
improper installation. Components may not be
connected securely and cause malfunctionor danger.
DO NOT OPERATE THE PRODUCT IN WAYS THAT
MAY DISTRACT YOUR ATTENTION FROM DRIVING.
Any operation that requires continued attention must be
done when the vehicle is at full stop. Always stop the
vehicle in a safe area when performing such operations.
Failure to do so maycause accidents.
MAINTAIN THE VOLUME AT LEVELS THAT ALLOW
EXTERNAL NOISES TO BEAUDIBLE WHILE DRIVING.
Excessive volume levels, capable of blocking the sound
of emergency vehicles, rail crossings, etc, may be
dangerous and cause accidents. Furthermore, listening
to audio at high volume inside a vehicle may cause
damage to your hearing.
IMPORTANT: CAREFULLY READ THIS MANUAL TO FAMILIARIZE YOURSELF WITH ALL THE CONTROLS AND FUNCTIONS OF THIS PRODUCT. FOLLOW ALL NOTICES TO
ENSURE THE SAFETY OF THOSE INSTALLING AND USINGTHE PRODUCT.
0 ~ 60°C
10 ~ 90%
WARNING!
DISCONNECT THE BATTERY LEADS
BEFORE INSTALLATION, MAINTENANCE
OR REMOVAL.
12V
WARNING!
USE ONLY IN VEHICLES WITH A 12 VOLT
NEGATIVE GROUND
MINIMUM CAPABILITY IMPEDANCE: 1OHM IN STEREO MODE; 2OHM IN BRIDGE MODE
is a brand of mos company di ivan mosconi - loc. ghilardino 61034 fossombrone (pu) italia - www.mos-hta.it
caratteristiche tecniche
4Ch4Ch
4Ch4Ch
4Ch
To Next Page
Need help?
General