The Mother's Choice Haven 4 Wheel 2 in 1 Stroller is a versatile and adaptable infant and toddler transport system designed for safety, comfort, and ease of use. This manual provides comprehensive instructions for assembly, operation, and maintenance, ensuring a secure and enjoyable experience for both parent and child.
Function Description:
The Haven stroller serves as a dual-purpose system, functioning as both a traditional stroller and a bassinet, making it suitable for newborns up to approximately 4.5 years of age (or 20kg). Its primary function is to provide a safe and comfortable means of transporting a child, offering various seating positions and configurations to adapt to the child's developmental stages and parental preferences. The 2-in-1 design allows for seamless transitions between a seated stroller and a flat bassinet mode, catering to the needs of infants who require a lie-flat position for rest and older children who can sit upright.
Usage Features:
Assembly and Setup:
- Opening the Stroller: The stroller features a storage latch that must be released before unfolding. To unfold, the handle is lifted with a swift motion until an audible 'click' confirms the locking mechanism is engaged. A check by pushing down on the handle ensures full engagement of the locks.
- Wheel Assembly: Rear wheels are attached by sliding them onto the axle, ensuring brake cogs face the axle. Retaining caps and hub caps then secure the wheels. The rear wheel assembly, including the axle and brakes, is then inserted into the stroller legs until it snaps into place, with red brake levers facing the rear. Front swivel wheels are attached by aligning the shaft with the hole in the front leg and pushing until a 'click' is heard. These wheels can be removed by pressing an internal push button.
- Canopy Assembly: The canopy is permanently attached to the stroller. It is assembled by aligning its plastic slides with the seat slides and pushing them towards the center. The canopy is then zipped around the seat.
- Seat Assembly: The seat is prepared by turning it over to expose the back, moving a metal bar down to the bottom, and securing press-stud straps to meet the bar on both sides.
- Fitting the Seat: The assembled seat is aligned with the frame and pushed downwards until a 'click' confirms it is locked in place. The seat can be removed by pressing release buttons on both sides and lifting.
- Bumper Bar Assembly: The bumper bar shafts are pushed into holes in the frame until they click, and can be removed by pressing grey buttons underneath.
Operating the Stroller:
- Canopy Use: The canopy can be extended by pulling its front edge forward, providing shade and protection.
- Brakes: The stroller is equipped with a brake system. To apply the brake, the brake lever is pressed down firmly. To release, the lever is pressed upwards. It is crucial to always apply the brakes whenever the stroller is stationary.
- Tether Strap: A tether strap is provided for added safety. This large loop should be worn around the user's wrist whenever a child is in the stroller and the brakes are not engaged, preventing the stroller from rolling away unintentionally.
- Stroller Seat Direction: The seat is reversible, allowing it to be used in either a world-facing or parent-facing direction. To change direction, the seat release buttons are pressed, the seat is lifted, turned around, and then pushed down until it locks into place.
- Adjusting Seat Position: The seat offers three recline positions for each direction. To adjust, a lever on the top of the seat is pulled upwards, and the seat is positioned as desired. When adjusting the backrest, ensure the child's limbs are kept inside the seating area.
- Using as a Bassinet: The stroller can be converted into a bassinet, recommended for newborns up to approximately 6 months or 9kg. This involves squeezing an adjuster clip and pulling downwards to set the backrest to its lowest, flat position. The two support strap clips below the seat are then unfastened, allowing the seat interior to fold out into the bassinet position. The bassinet can be used in both world-facing and parent-facing orientations. It is important to note that the bassinet cannot stand alone and should not be used once the child can sit up unaided.
- Securing Your Child (Harness System): The stroller features a 5-point safety harness system. Shoulder straps are slipped over each shoulder, and the crotch strap is positioned between the legs. Buckle prongs are inserted into the buckle housing until they click, ensuring the harness is locked. Straps can be tightened or loosened by lifting the plastic adjuster. The waist strap should fit firmly around the child. The buckle is released by squeezing the top and bottom prongs simultaneously.
- Adjusting Harness Height: The harness can be set at three different heights to accommodate the child's growth. To adjust, the buckle is undone, and the shoulder straps are fed through the chosen loop (lower, middle, or upper slot) before re-securing the harness.
- Folding the Stroller with Seat: Before folding, the canopy should be folded back, the seat backrest adjusted to an upright position, swivel wheels unlocked, and rear brakes applied. A button is then pushed and held while simultaneously squeezing the handle button to release the lock. The handle is pushed downwards to fold the stroller. The storage latch will automatically engage when fully folded. Ensure the seat is facing world-facing when folding.
- Unfolding the Stroller: To unfold, the storage latch is released, the handle is lifted until the stroller is fully open and the locking mechanism engages, and then the handle is pushed down to ensure locks are fully engaged.
- Carrying the Stroller: Once folded and the storage latch is applied, the stroller can be carried by holding the frame between the rear wheel and the storage latch. The stroller can be folded with or without the seat.
Maintenance Features:
- Storage: Always store the stroller in a clean and dry place to prevent damage and maintain its condition.
- Cleaning: The frame should be cleaned by wiping it with a damp cloth. Abrasives, bleach, or strong detergents should not be used as they can damage the materials. Fabrics can be spot cleaned with warm water and mild soap, and it is essential to ensure the fabric is completely dry before storing to prevent mildew.
- Lubrication: The wheels should be occasionally cleaned and lubricated with a light lubricating oil to ensure smooth operation and extend their lifespan.
- Inspection: Regular inspection of all parts and locking devices is crucial. Any loose parts should be tightened promptly, and worn out or broken parts must be replaced immediately to maintain safety and functionality.
- Accessories: Only accessories supplied by Dorel Australia and approved for use with this stroller should be used.
- Safety Precautions: To prevent the risk of fire, the stroller should not be parked near an open fire, heater, or barbecue. Caution should be exercised when folding or unfolding the stroller to avoid injury to fingers or other body parts from moving components.
The Mother's Choice Haven 4 Wheel 2 in 1 Stroller is designed with a focus on safety, adaptability, and user convenience, providing a reliable solution for transporting young children through various stages of their early development.
Need help?
General
To Next Page