Need help?Do you have a question about the MPH Industries BEE III and is the answer not in the manual?
General| Brand | MPH Industries |
|---|---|
| Model | BEE III |
| Category | Radar Detector |
| Language | English |
How mounting affects radar targeting distance and how to optimize placement for best results.
Discusses power sources and recommendations for optimal performance and interference reduction.
Instructions for replacing the fuse in the cigarette lighter plug for the radar unit.
Explains the pictorial view of radar functions and operating modes like stationary and moving.
Describes the three speed display windows (red, yellow, green) and their functions.
Explains the purpose and function of the Doppler audio speaker and its relation to target speed.
Details the automatic display brightness adjustment and infrared sensor for remote control.
Describes the function of the power button and its effect on radar settings.
Explains the raised rubber buttons on the remote for selecting operating modes and their ergonomic design.
Details the functions of the flat membrane buttons on the lower section of the remote control.
Explains the function of the "2nd F" button for accessing secondary functions on the remote.
Notes that the "Backlt" button has no function for wired remote controls.
How to adjust the audio volume using the menu button and volume controls.
How to adjust the squelch setting (on/off) using the menu button and volume controls.
How to adjust the dynamic stationary mode setting via the menu.
How to adjust the radar's range setting using the menu button and volume controls.
How to initiate POP mode through the menu system.
Describes how to operate the radar in stationary mode to monitor traffic.
Explains how to use the radar in moving mode to track approaching and receding vehicles.
Details how to operate the radar in same direction moving mode to track vehicles moving in the same direction.
Explains the use of the radar in pacing mode, functioning as a calibrated speedometer.
How to use the fastest mode to identify the speed of the fastest vehicle.
Explains the POP mode for quick speed checks without alerting vehicles.
Guidance on the best scenarios and methods for effectively using POP mode.
Discusses the detection effectiveness of POP mode against radar detectors.
Cautionary advice regarding issuing offense notices based solely on POP mode readings.
Details how to measure vehicle speed using stopwatch mode without microwave transmission.
Further explanation on using stopwatch mode, including landmark setup and timer operation.
Discusses operational considerations and points to remember when using the fastest mode.
Explains the operation of the moving same direction mode, including ASDTM technology.
Key points and considerations for operating the radar in same direction mode.
Describes the self-test procedure performed when the BEE III radar is initially powered on.
Step-by-step instructions for performing a manual self-test of the radar unit.
Guidelines for conducting a road test to verify the radar's accuracy and performance.
Discusses natural factors like weather and terrain that can affect radar performance.
Explains man-made electronic influences that can cause spurious readings or reduce range.
Addresses fan interference and provides suggestions from MPH Industries to mitigate it.
Instructions on how to power on the BEE III radar unit.
Guide on performing a self-test to ensure the radar is functioning correctly.
Steps to select and understand different operating modes of the BEE III radar.
Guidance on using the radar in stationary mode and selecting target directions.
Instructions on how to lock a target speed and interpret the display indicators.
How to navigate and use the menu system for adjusting settings like audio and squelch.
How to use the fastest button on the remote to activate fastest target mode.
Steps to find and lock targets using the radar in stationary mode.
How to find and lock targets while operating in moving opposite direction mode.
How to find and lock targets while operating in moving same direction mode.
Information on obtaining calibration and certification services for the radar unit.
Availability and importance of ordering spare remote controls for the BEE III.
Information on the variety of mounting brackets available for the BEE III.
How to order the comprehensive service manual for the BEE III.
Information on obtaining additional copies of the operation manual.
Details the speedometer interface module and its function in improving radar accuracy.
Information about the specialized BEE III version designed for motorcycle use.
Procedures and guidelines for warranty repairs of the BEE III radar unit.
Recommendations for performing repairs on the BEE III radar outside of the warranty period.
Details the terms and conditions of the MPH Industries product warranty for the BEE III.
Presents the certification information granted by Industry Canada for the Ka band BEE III unit.
Lists key system specifications for the BEE III radar, including voltage, current, and speed ranges.
Describes the components and features of the BEE III display unit, including windows and indicators.
Details the connectors and physical size specifications for the BEE III counting unit.
Lists specifications for the BEE III remote control, including backlighting, keys, and physical size.
Provides specifications for the BEE III antenna unit, including operating frequency, power, and physical size.
Recommends proper antenna mounting to minimize operator exposure to microwave energy.
Advises on periodic testing of radar antennas for radiation leakage or back scatter.
Emphasizes the importance of operator training on radar use and health risks.
To Next Page
