EasyManua.ls Logo

MQ Power DCA220SSJU4F - User Manual

MQ Power DCA220SSJU4F
80 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
To find the latest revision of this
publication, visit our website at:
www.mqpower.com
WHISPERWATT™ SERIES
MODEL DCA220SSJU4F
60Hz GENERATOR
(JOHN DEERE 6068HFG09 DIESEL ENGINE)
Revision #3 (02/10/17)
OPERATION MANUAL

Table of Contents

Questions and Answers

  • C
    Courtney MitchellAug 2, 2025
    What to do if the circuit breaker tripped on my MQ Power DCA220SSJU4F?
    • K
      Kimberly YoungAug 2, 2025
      If your MQ Power Inverter's circuit breaker tripped, it could be due to a short circuit in the load. Check the load and repair any issues. It might also be because of an overcurrent situation; confirm the load requirements and reduce them if necessary. A defective circuit breaker could also be the culprit, so check and replace it if needed. Finally, an overcurrent relay might have actuated, in which case you should confirm the load requirement and replace the relay.
  • S
    Scott AlexanderAug 10, 2025
    How to troubleshoot no voltage output on MQ Power DCA220SSJU4F?
    • C
      Connor KelleyAug 10, 2025
      If your MQ Power Inverter has no voltage output, start by checking the output voltage using a voltmeter to rule out a defective AC voltmeter. Then, inspect the wiring for any loose connections and repair them. If the issue persists, the AVR might be defective and require replacement. Also, check and replace the rotating rectifier if necessary. Finally, check the exciter field for approximately 19 ohms across J & K on CN1.
  • J
    Jacqueline GordonAug 17, 2025
    Why is the voltage output low on my MQ Power DCA220SSJU4F Inverter?
    • E
      Erin MaciasAug 17, 2025
      If your MQ Power Inverter is showing a low voltage output, first ensure the engine speed is correct by turning the engine throttle lever to “High.” Also, check the wiring for any loose connections and repair them. If the problem continues, the AVR may be defective and need replacement.
  • T
    taylorsheliaAug 25, 2025
    What causes high voltage output in MQ Power DCA220SSJU4F Inverter?
    • C
      Cynthia JohnsonAug 26, 2025
      If your MQ Power Inverter is showing a high voltage output, begin by inspecting the wiring connections for any looseness and repair them as needed. If the issue persists, the AVR may be defective and require replacement.

Summary

Safety Information

Safety Messages and Symbols

Explains the four safety message levels and lists hazard symbols and their meanings.

General and Generator Safety Precautions

Provides general operating safety guidelines and specific measures for generator operation.

Engine Safety Precautions

Covers hazards and safety measures related to the engine.

Fuel and Towing Safety

Outlines dangers and safe handling of fuel and towing the generator.

Electrical, Grounding, and Battery Safety

Details risks and safety for electrical connections, grounding, and battery handling.

Specifications

Installation

Generator Grounding

Explains the importance and method of grounding the generator for safety.

General Paralleling Information (Option)

Paralleling, Load Sharing, and Communication

Explains load sharing, Ethernet communication for paralleling, and load management.

3-Phase Parallel Wiring and Ethernet Connection

Procedure for 3-phase wiring and Ethernet connection for paralleling.

Major Components

Generator Component Identification

Identifies and lists the main components of the generator with item numbers.

Basler Digital Genset Controller (Option)

DGC-2020 HD Overview and Controls

Details the touch screen display, indicators, and pushbutton functions.

Paralleling Panel (Option)

Contactor Operation and Paralleling

Explains how to operate contactors for manual and paralleling modes.

Generator Output Voltages

Available Output Voltages

Explains how to select voltages using the change-over board.

Generator Maximum Amperage

Generator Start-Up Procedure (Manual)

Before Starting Checks (Manual)

Pre-start checks including breakers and voltage configuration.

Manual Engine Start and Monitoring

Step-by-step guide to start engine manually and monitor gauges.

Generator Start-Up Procedure (Auto Mode)

Auto Mode Startup Process

Steps for starting the generator in automatic mode.

Generator Shut-Down Procedures

Normal Engine Shutdown

Steps for a standard generator shutdown procedure.

Emergency Engine Shutdown

How to perform an emergency shutdown.

Maintenance

Inspection and Maintenance Schedule

Details routine inspection and maintenance tasks and intervals.

DPF Regeneration Procedures

Automatic Regeneration and Diagnostics

Generator Wiring Diagram

Wiring Diagram and Component Symbols

Illustrates the generator's wiring and defines component symbols.

Generator Wiring Diagram (Basler Option)

Basler DGC-2020 Wiring Diagram

Wiring diagram for the Basler DGC-2020 controller option.

Engine Wiring Diagram (ECU 835)

ECU 835 Engine Control Wiring

Wiring diagram for the ECU 835 engine controller.

Engine Wiring Diagram (Basler DGC2020 HD Option)

Basler DGC2020 Engine Control Wiring

Wiring diagram for the Basler DGC2020HD engine controller.

30-208 VAC Parallel Wiring Diagram

Camlok Parallel Wiring Connections

Diagram for 3-phase 208 VAC parallel wiring via camlocks.

Generator Troubleshooting

Troubleshooting Common Generator Issues

Table of symptoms, possible problems, and solutions for generator issues.

Troubleshooting Diagnostics

Accessing Fault Diagnostics

Steps to access and view fault diagnostics on the ECU.

Basler DGC-2020 Programming Appendix (Option)

DGC-2020 Touch Screen Operation

MQ Power DCA220SSJU4F Specifications

General IconGeneral
BrandMQ Power
ModelDCA220SSJU4F
CategoryInverter
LanguageEnglish

Related product manuals