Do you have a question about the MSI GE70 MS-1756 and is the answer not in the manual?
Move the 'Unlock' button base to release the battery.
Release the 'Release' button and slide out the battery pack.
Remove 6 screws (M2.5*5.5mm) to detach the bottom door.
Remove 2 screws (M2.5*5.5mm) and detach the HDD module.
Remove 2 screws (M3*4mm) and detach the HDD bracket.
Remove 2 screws (M2.5*5.5mm) and fan cable to detach the fan.
Remove 8 screws (M2.5*4.5mm) to detach the heatsink.
Open CPU slot and remove the CPU module.
Push RAM side shields and remove the RAM module.
Remove 1 screw (M2*3.5mm) and detach the wireless antenna.
Remove the ODD module as shown in the picture.
Detach the ODD bezel as illustrated.
Remove 2 screws (M2*3mm) and detach the ODD bracket.
Release keyboard hooks and remove the keyboard assembly.
Push connector and remove the cable.
Open connector, then remove power board and touchpad cable.
Remove 5 screws (M2*3.5mm).
Remove 10 screws (M2.5*5.5mm).
Remove 11 screws (M2.5*5.5mm).
Detach the speaker and MIC cable.
Detach the LVDS and power cable as shown.
Remove 2 screws (M2.5*5.5mm) to detach the upper case.
Remove 3 screws (M2.5*4.5mm) and detach the Left I/O board.
Remove FFC, 2 screws (M2.5*4.5mm), then detach T/P board.
Remove 3 screws (M2.5*4.5mm) and detach the main board.
Remove Bluetooth cable and 1 screw (M2.5*4.5mm) to detach Right I/O board.
Remove 2 screws (M2.5*5.5mm) securing the left LCD hinge.
Remove 2 screws (M2.5*5.5mm) securing the right LCD hinge.
Remove 1 screw (M2.5*5.5mm) and detach the power connector.
Detach the speaker assembly.
Remove 2 screws (M2*3.5mm) and detach the power board.
Remove 1 screw (M2*3.5mm) and detach the USB board.
Release connector and detach the Touchpad/Power module.
Remove the 4 cover rubbers.
Remove LCD bezel starting from the top, then sides.
Remove 1 screw (M2.5*4mm) and detach the left hinge cap.
Remove 1 screw (M2.5*4.5mm) and detach the right hinge cap.
Remove 4 screws (M2.5*4.5mm) securing the left hinge.
Remove 4 screws (M2.5*4.5mm) securing the right hinge.
Remove 4 screws (M2.5*4.5mm), camera cable, and display module.
Detach the LVDS cable from the display module.
Remove 8 screws (M2*3mm).
Remove the CMOS camera module as pictured.
Remove the CMOS camera module as pictured.
Remove the Wireless Antenna board from the LCD cover.
Move the 'Unlock' button base to release the battery.
Release the 'Release' button and slide out the battery pack.
Remove 6 screws (M2.5*5.5mm) to detach the bottom door.
Remove 2 screws (M2.5*5.5mm) and detach the HDD module.
Remove 2 screws (M3*4mm) and detach the HDD bracket.
Remove 2 screws (M2.5*5.5mm) and fan cable to detach the fan.
Remove 8 screws (M2.5*4.5mm) to detach the heatsink.
Open CPU slot and remove the CPU module.
Push RAM side shields and remove the RAM module.
Remove 1 screw (M2*3.5mm) and detach the wireless antenna.
Remove the ODD module as shown in the picture.
Detach the ODD bezel as illustrated.
Remove 2 screws (M2*3mm) and detach the ODD bracket.
Release keyboard hooks and remove the keyboard assembly.
Push connector and remove the cable.
Open connector, then remove power board and touchpad cable.
Remove 5 screws (M2*3.5mm).
Remove 10 screws (M2.5*5.5mm).
Remove 11 screws (M2.5*5.5mm).
Detach the speaker and MIC cable.
Detach the LVDS and power cable as shown.
Remove 2 screws (M2.5*5.5mm) to detach the upper case.
Remove 3 screws (M2.5*4.5mm) and detach the Left I/O board.
Remove FFC, 2 screws (M2.5*4.5mm), then detach T/P board.
Remove 3 screws (M2.5*4.5mm) and detach the main board.
Remove Bluetooth cable and 1 screw (M2.5*4.5mm) to detach Right I/O board.
Remove 2 screws (M2.5*5.5mm) securing the left LCD hinge.
Remove 2 screws (M2.5*5.5mm) securing the right LCD hinge.
Remove 1 screw (M2.5*5.5mm) and detach the power connector.
Detach the speaker assembly.
Remove 2 screws (M2*3.5mm) and detach the power board.
Remove 1 screw (M2*3.5mm) and detach the USB board.
Release connector and detach the Touchpad/Power module.
Remove the 4 cover rubbers.
Remove LCD bezel starting from the top, then sides.
Remove 1 screw (M2.5*4mm) and detach the left hinge cap.
Remove 1 screw (M2.5*4.5mm) and detach the right hinge cap.
Remove 4 screws (M2.5*4.5mm) securing the left hinge.
Remove 4 screws (M2.5*4.5mm) securing the right hinge.
Remove 4 screws (M2.5*4.5mm), camera cable, and display module.
Detach the LVDS cable from the display module.
Remove 8 screws (M2*3mm).
Remove the CMOS camera module as pictured.
Remove the CMOS camera module as pictured.
Remove the Wireless Antenna board from the LCD cover.