To Next PageTo Next Page
Need help?Do you have a question about the MTL MTL5000 Series and is the answer not in the manual?
General| Brand | MTL |
|---|---|
| Model | MTL5000 Series |
| Category | Recording Equipment |
| Language | English |
Details on installing unenclosed isolators, including orientation and spacing.
Instructions for mounting MTL5000 isolators on T35 DIN rail, including removal.
Guidance on wiring MTL5000 isolators, including connector types and cable preparation.
Explains phase reversal switches on MTL5000 modules and their settings.
Details on Line Fault Detection (LFD) for MTL5000 modules and its indications.
Info on reactive loads and recommended switching current for MTL5000 relay outputs.
How to use MTL4220 earth leakage detector with MTL5000 Series units.
Ambient temperature limits for unenclosed MTL5000 Series isolators.
Instructions for installing and using the MTL5000 Series power bus kits.
Information on specifying and assembling earth rail and tagging strip accessories.
Environmental conditions to consider when installing DX enclosures, including temperature and humidity.
Instructions and details for mounting DX enclosures, including location and orientation.
Requirements for cable glanding into DX enclosures to maintain IP65 standards.
Description of MTL5011 for safe-area load control via hazardous-area switch/detector.
Details of MTL5011B, similar to MTL5011 but with Line Fault Detection.
Description of MTL5012 for solid-state load control with LFD and phase reversal.
Description of MTL5014 for dual load control with LFD and phase reversal.
Description of MTL5015 for dual load control with LFD and phase reversal.
Description of MTL5016 for dual load control with phase reversal.
Description of MTL5017, similar to MTL5018 with LFD.
Description of MTL5018 for dual load control with LFD and phase reversal.
Description of MTL5018AC, similar to MTL5018 with LFD.
Description of MTL5021 for controlling hazardous-area devices via safe-area switch.
Description of MTL5022 for controlling hazardous-area devices via safe-area switch.
Description of MTL5023 with LFD and phase reversal for load control.
Description of MTL5024 with logic drive and phase reversal for load control.
Description of MTL5025 for controlling hazardous-area devices via safe-area switch.
Description of MTL5031 for interfacing vibration sensors to a safe-area system.
Description of MTL5032 for isolating pulses from hazardous-area transmitters.
Description of MTL5040 for isolating 4 to 20mA signals and providing DC supply.
Description of MTL5041/42 for providing DC supplies to transmitters and repeating current.
Description of MTL5043 for dual output supplies to transmitters and driving loads.
Description of MTL5044 for two repeater supplies and driving two loads.
Description of MTL5045/46 for isolating and passing 4-20mA signals.
Description of MTL5048 loop-powered isolator for analogue input/output.
Description of MTL5049 for isolating and passing two 4-20mA signals.
Description of MTL5051 for bi-directional serial data communications.
Description of MTL5053 for 31.25kbit/s fieldbus networks, providing power and isolation.
Description of MTL5061 for isolating fire/smoke detectors and providing alarm output.
Description of MTL5074 for converting temperature sensor signals to 4-20mA.
Description of MTL5081 for isolating low-level DC signals from hazardous areas.
Description of MTL5082 for isolating RTD or resistance inputs.
Description of MTL5099 dummy isolator for termination and earthing.
Description of MTL5113P for fail-safe sensor control with LFD alarm.
Description of MTL5314 trip amplifier for 2/3-wire transmitters with alarm signals.
Description of MTL5344 for repeater power supplies and driving safe-area loads.
Description of MTL5349 for isolating and passing two 4-20mA signals.
Description of MTL5991 24V DC power supply for MTL5000 Series units.
Description of MTL5995 fieldbus power supply for 31.25kbit/s systems.
Guidelines for routine checks to ensure correct installation and condition of isolators.
Maintenance requirements for enclosures, including cleaning and inspection.
Description of MTL5521 for rotational speed monitoring with over/under-speed detection.
Description of MTL5531 for converting hazardous-area current/voltage inputs.
Description of MTL5536 for repeating potentiometer input as an analogue signal.
