What does Error Status mean on MTU 16V4000L32FB Engine?
If your MTU Engine is showing an Error Status, it means there is a GET combined alarm and at least one other GET alarm is pending. Rectify the cause of the alarm.
What to do if HIHI T-Exhaust Mean error appears on my MTU 16V4000L32FB Engine?
If you encounter a HIHI T-Exhaust Mean error on your MTU Engine, it means the weighted average of all individual exhaust gas temperatures is too high. To resolve this, check the emission values, ignition timing, and ensure the exhaust valves are closing correctly by inspecting the valve drive.
What causes Input Supply Voltage High Error on MTU Engine and how to fix it?
If you're getting an Input Supply Voltage High Error on your MTU Engine, it means the supply voltage has reached its maximum limit. To fix this, check both the supply voltage and the cabling.
Why does my MTU 16V4000L32FB Engine show Input Supply Voltage Low Error?
An Input Supply Voltage Low Error on your MTU Engine indicates that the supply voltage has dropped to its minimum limit. You should check the supply voltage and the cabling to resolve this issue.
How do I fix HI T-Exhaust A1 error on my MTU 16V4000L32FB Engine?
If the exhaust temperature of cylinder A1 is too high compared to the average on your MTU Engine, check the emission values, ignition timing, and valve drive, making sure the exhaust valves are closing correctly.
How to fix Internal Error on MTU Engine?
If your MTU Engine displays an Internal Error, this indicates that the hardware is not ready for operation. Restart the knock module to resolve this.
What to do if FGP Fail Low error appears on MTU Engine?
If you're seeing an FGP Fail Low error on your MTU Engine, it means the gas pressure before the TecJet is below the preset limit. Check the TecJet and its configuration.
Why does my MTU 16V4000L32FB Engine show Delta P Fail Low error?
If a Delta P Fail Low error occurs on your MTU Engine, it means the delta-p via TecJet is below the set limit value. Check the TecJet and its configuration.
How can I fix HI T-Exhaust A8 error on my MTU 16V4000L32FB?
If you get a HI T-Exhaust A8 error on your MTU Engine, it signifies that the exhaust temperature of cylinder A8 is too high. Check the emission values, ignition timing, and the valve drive, ensuring the exhaust valves close properly.
What are the possible causes of HI T-Exhaust A6 error on MTU 16V4000L32FB Engine?
A HI T-Exhaust A6 error on your MTU Engine indicates that the exhaust temperature of cylinder A6 is too high relative to the average. You should check the emission values, ignition timing, and the valve drive, making sure the exhaust valves are closing properly.
Key guidelines for product operation and safety.
Requirements for personnel involved in operation and maintenance.
Procedures and safety for engine transportation.
Essential safety rules for starting and operating the engine.
Specific safety rules for gaseous fuel engine operation.
Safety precautions for maintenance and repair activities.
Specific safety for gaseous fuel maintenance and repair.
Guidelines for fire safety, environmental protection, and material handling.
Specific fire/environmental rules for gaseous fuel applications.
Explanation of safety notice symbols and their meanings.
Identification of engine components and their locations.
Standardized naming for engine sides and cylinders.
Key physical dimensions of the engine.
Sequence of cylinder ignition for proper engine operation.
Detailed technical specifications and operating parameters.
Overview of systems for engine monitoring and control.
Guidelines for engine operation at partial load conditions.
Procedures for restarting an engine after long storage.
Steps for restarting after a short, planned shutdown.
Detailed steps for engine start-up, shutdown, and emergency stops.
Preconditions and procedure for starting the engine.
Routine checks to ensure proper engine operation.
Procedure for checking engine emission values.
Procedures for safely shutting down the engine.
Actions and procedures for emergency engine shutdown.
Information on engine status after stopping.
Procedures for taking the engine out of service for extended periods.
Specific checks required after the first 50 operating hours.
A reference table for various maintenance tasks and procedures.
Explanation of abbreviations and codes used for fault messages.
Troubleshooting specific fault messages related to the genset control system.
Fault messages and corrective actions specific to the engine governor.
General engine tasks and procedures.
Manual procedure for rotating the engine crankshaft.
Safety procedure for detecting gas leaks in the engine room.
Maintenance and replacement of the crankcase breather's oil separator.
Step-by-step guide to replacing the oil separator filter.
Tasks related to the engine's ignition system.
Procedure for replacing spark plugs.
Steps for safely removing a spark plug.
Steps for correctly installing a spark plug.
Procedure for replacing the spark plug connector.
Steps for removing the spark plug connector.
Steps for installing the spark plug connector.
Procedure for checking and adjusting ignition timing.
Tasks related to the engine's valve drive system.
Procedure for measuring valve depth.
Procedure for checking and adjusting valve clearance.
Lubrication procedure for the valve gear.
Steps for removing the cylinder head cover.
Steps for installing the cylinder head cover.
Procedures related to the engine's gas supply system.
Procedure for checking gas lines for leaks.
Maintenance and replacement of the air filter.
Steps for replacing the air filter.
Procedure for removing and installing the air filter.
Tasks related to the engine's lube oil system.
Procedure for checking the engine oil level.
Procedure for changing the engine oil.
Procedure for taking and analyzing engine oil samples.
Maintenance of the oil filtration and cooling system.
Procedure for replacing the engine oil filter.
Maintenance of the high-temperature coolant circuit.
Procedure for checking the engine coolant level.
Procedure for changing the engine coolant.
Procedure for draining the engine coolant.
Procedure for filling the engine coolant.
Procedure for replacing the engine coolant vent line.
Maintenance of the low-temperature coolant circuit.
Procedure for checking the mixture coolant level.
Procedure for changing the mixture coolant.
Procedure for draining the mixture coolant.
Procedure for filling the mixture coolant.
General check of engine wiring and connections.
Procedure for checking engine wiring and components.
Identification and location of engine sensors.
Glossary of abbreviations used in the manual.
Contact information for support and service.
List of special tools required for maintenance tasks.
Key guidelines for product operation and safety.
Requirements for personnel involved in operation and maintenance.
Procedures and safety for engine transportation.
Essential safety rules for starting and operating the engine.
Specific safety rules for gaseous fuel engine operation.
Safety precautions for maintenance and repair activities.
Specific safety for gaseous fuel maintenance and repair.
Guidelines for fire safety, environmental protection, and material handling.
Specific fire/environmental rules for gaseous fuel applications.
Explanation of safety notice symbols and their meanings.
Identification of engine components and their locations.
Standardized naming for engine sides and cylinders.
Key physical dimensions of the engine.
Sequence of cylinder ignition for proper engine operation.
Detailed technical specifications and operating parameters.
Overview of systems for engine monitoring and control.
Guidelines for engine operation at partial load conditions.
Procedures for restarting an engine after long storage.
Steps for restarting after a short, planned shutdown.
Detailed steps for engine start-up, shutdown, and emergency stops.
Preconditions and procedure for starting the engine.
Routine checks to ensure proper engine operation.
Procedure for checking engine emission values.
Procedures for safely shutting down the engine.
Actions and procedures for emergency engine shutdown.
Information on engine status after stopping.
Procedures for taking the engine out of service for extended periods.
Specific checks required after the first 50 operating hours.
A reference table for various maintenance tasks and procedures.
Explanation of abbreviations and codes used for fault messages.
Troubleshooting specific fault messages related to the genset control system.
Fault messages and corrective actions specific to the engine governor.
General engine tasks and procedures.
Manual procedure for rotating the engine crankshaft.
Safety procedure for detecting gas leaks in the engine room.
Maintenance and replacement of the crankcase breather's oil separator.
Step-by-step guide to replacing the oil separator filter.
Tasks related to the engine's ignition system.
Procedure for replacing spark plugs.
Steps for safely removing a spark plug.
Steps for correctly installing a spark plug.
Procedure for replacing the spark plug connector.
Steps for removing the spark plug connector.
Steps for installing the spark plug connector.
Procedure for checking and adjusting ignition timing.
Tasks related to the engine's valve drive system.
Procedure for measuring valve depth.
Procedure for checking and adjusting valve clearance.
Lubrication procedure for the valve gear.
Steps for removing the cylinder head cover.
Steps for installing the cylinder head cover.
Procedures related to the engine's gas supply system.
Procedure for checking gas lines for leaks.
Maintenance and replacement of the air filter.
Steps for replacing the air filter.
Procedure for removing and installing the air filter.
Tasks related to the engine's lube oil system.
Procedure for checking the engine oil level.
Procedure for changing the engine oil.
Procedure for taking and analyzing engine oil samples.
Maintenance of the oil filtration and cooling system.
Procedure for replacing the engine oil filter.
Maintenance of the high-temperature coolant circuit.
Procedure for checking the engine coolant level.
Procedure for changing the engine coolant.
Procedure for draining the engine coolant.
Procedure for filling the engine coolant.
Procedure for replacing the engine coolant vent line.
Maintenance of the low-temperature coolant circuit.
Procedure for checking the mixture coolant level.
Procedure for changing the mixture coolant.
Procedure for draining the mixture coolant.
Procedure for filling the mixture coolant.
General check of engine wiring and connections.
Procedure for checking engine wiring and components.
Identification and location of engine sensors.
Glossary of abbreviations used in the manual.
Contact information for support and service.
List of special tools required for maintenance tasks.
General| Engine Type | Diesel |
|---|---|
| Cylinders | 16 |
| Bore | 165 mm |
| Stroke | 190 mm |
| Speed | 1800 rpm |
| Compression Ratio | 16.5:1 |
| Aspiration | Turbocharged and intercooled |
| Emission Standards | IMO Tier II, EPA Tier 2 |
| Configuration | V-Engine |
| Displacement | 32.4 L |
| Cooling System | Water-cooled |
To Next Page
