26
Blizzard KIT
Part No. Description Material Dimensions
No. off
1 1 KIT building instructions Paper, 80 g/m² A4
2 1 Decal set Printed adhesive film 330 x 700 mm
3 1 L.H. fuselage shell Moulded Elapor foam Ready made
4 1 R.H. fuselage shell Moulded Elapor foam Ready made
5 1 L.H. wing panel Moulded Elapor foam Ready made
6 1 R.H. wing panel Moulded Elapor foam Ready made
7 1 L.H. V-tail panel Moulded Elapor foam Ready made
8 1 R.H. V-tail panel Moulded Elapor foam Ready made
9 1 Front wing spar Rectangular CFRP tube 6 x 4 x 800 mm
10 1 Rear wing spar Rectangular CFRP tube 6 x 4 x 700 mm
11 1 GRP longeron (coil) GRP 1.3 Ø x 8500 mm
12 1 Canopy Inj. moulded plastic Ready made
13 1 Front fuselage fairing / motor bulkhead Inj. moulded plastic Ready made
14 2 Rear fuselage fairing Inj. moulded plastic Ready made
15 1 Wing centre section doubler Inj. moulded plastic Ready made
16 4 Spar cover sticker Self-adhesive plastic 13 x 400 mm
Small items set
20 3 Velcro tape, “mushroom” Plastic 25 x 60 mm
21 3 Velcro tape, “felt” Plastic 25 x 60 mm
22 2 Canopy latch Inj. moulded plastic Ready made
23 2 Canopy latch tongue Inj. moulded plastic Ready made
24 4 Glue-fitting ‘Twin’ control surface horn Inj. moulded plastic Ready made
25 4 Swivel pushrod connector barrel Metal Ready made, 6 mm Ø
26 4 Socket-head grubscrew Metal M3 x 3 mm
27 1 Allen key Metal 1.5 mm A/F
28 2 Aileron pushrod, one Z-bend Metal 1 Ø x 60 mm
29 2 V-tail pushrod Metal 1 Ø x 115 mm
30 2 Elevator pushrod, one Z-bend Metal 1 Ø x 145 mm
31 2 Countersunk wing retainer screw Plastic M5 x 20 mm
32 2 Nut (wing retainer plate) Metal M5
33 2 Screw (glider nose-cone) Metal M3 x 16 mm
34 1 Screw (trim compartment cover) Metal 2.2 x 6.5 mm
35 3 Trim ballast, electric version Steel ball, 9 g 13 mm Ø
36 2 Servo compartment cover, top Plastic 35 x 35 mm
Plastic parts set
40 1 Wing retainer plate Inj. moulded plastic Ready made
41 1 Trim ballast chamber cover Inj. moulded plastic Ready made
42 1 Glider nose-cone Inj. moulded plastic Ready made
43 1 Spacer ring, 39 Ø x 4 mm Inj. moulded plastic Ready made
44 1 L.H. servo fairing Inj. moulded plastic Ready made
45 1 R.H. servo fairing Inj. moulded plastic Ready made
Spars and longerons
11 1 Spar caps and fuselage longerons (roll, 1.3 Ø x 8500 mm)
11.1 2 Bottom tailplane spar cap GRP rod 1.3 Ø x 160 mm
11.2 2 Top tailplane spar cap GRP rod 1.3 Ø x 171 mm
11.3 1 Bottom wing spar cap GRP rod 1.3 Ø x 1345 mm
11.4 1 Top wing spar cap GRP rod 1.3 Ø x 1345 mm
11.5 2 L.H. / R.H. fuselage longeron GRP rod 1.3 Ø x 700 mm
11.6 1 Bottom fuselage longeron GRP rod 1.3 Ø x 723 mm
11.7 1 Top fuselage longeron GRP rod 1.3 Ø x 495 mm
11.8 2 L.H. / R.H. inner fuselage longeron GRP rod 1.3 Ø x 126 mm
11.9 20 Diagonal wing brace GRP rod 1.3 Ø x various
16 4 Spar cover sticker Plastic 13 x 400 mm
To Next Page
Loading...
