17
GB
Always y in such a way that you do not endanger yourself or others. Bear in mind that even the best RC system in the
world is subject to outside interference. No matter how many years of accident-free ying you have under your belt, you
have no idea what will happen in the next minute.
Before every ight, check that the battery, the wings and the tailplane are attached and rmly seated. Check in
turn that each control surface is operating correctly!
We - the MULTIPLEX team - hope you have many hours of pleasure building and ying your new model.
MULTIPLEX Modellsport GmbH &Co. KG
Parts List ParkMaster PRO KIT # 21 4275
Part No. Description Material Dimensions
No. off
1 1 Building instructions Paper 80g/m² DIN-A4
2 “A” 1 Decal sheet Printed adhesive lm 500 x 750mm
2 “B” 1 Decal sheet Printed adhesive lm 500 x 750mm
3 1 Fuselage Moulded Elapor foam Ready made
4 1 L.H. wing Moulded Elapor foam Ready made
5 1 R.H. wing Moulded Elapor foam Ready made
6 1 L.H. aileron Moulded Elapor foam Ready made
7 1 R.H. aileron Moulded Elapor foam Ready made
8 1 Tailplane Moulded Elapor foam Ready made
9 1 Elevator Moulded Elapor foam Ready made
10 1 Rudder Moulded Elapor foam Ready made
11 1 L.H. undercarriage leg fairing Moulded Elapor foam Ready made
12 1 R.H. undercarriage leg fairing Moulded Elapor foam Ready made
CFRP strip
13 2 Undercarriage leg CFRP 10 x 1.5 x 144 mm
14 2 Fuselage longeron CFRP 3.0 x 1.0 x 743 mm
15 2 Wing spar CFRP 3.0 x 1.0 x 850 mm
16 1 Elevator spar CFRP 3.0 x 1.0 x 400 mm
17 2 Forward fuselage stiffener CFRP 3.0 x 1.0 x 120 mm
18 2 Wheel axle CFRP 2.5 Ø x 32 mm
Small parts set
20 2 Hook-and-loop tape, hook Plastic 25 x 60mm
21 2 Hook-and-loop tape, loop Plastic 25 x 60mm
22 3 Leaf hinge (sprue of 6) Inj. moulded plastic Ready made
23 4 Glue-tting control surface horn Inj. moulded plastic Ready made
24 4 Swivel pushrod connector Metal Ready made, 6 mm Ø
25 4 Washer Metal M2
26 4 Nut Metal M2
27 4 Socket-head grubscrew Metal M3 x 3mm
28 1 Allen key Metal 1.5 mm A/F
29 2 Pre-formed aileron pushrod Metal 1 Ø x 70 mm
30 1 Pre-formed elevator pushrod Metal 1 Ø x 85 mm
31 1 Pre-formed rudder pushrod Metal 1 Ø x 115 mm
32 1 Firewall Inj. moulded plastic Ready made
33 4 Socket-head screw, rewall adjustment Metal M3 x 10 mm
34 2 Socket-head screw, rewall mounting Metal M3 x 12 mm
35 1 Firewall support Inj. moulded plastic Ready made
36 1 Front undercarriage support Inj. moulded plastic Ready made
37 1 Rear undercarriage support Inj. moulded plastic Ready made
38 2 Lightweight wheel EPP plastic 53 Ø, hub bore 2.6 mm
39 4 Starlock washer (wheel retainer) Metal for 2 mm Ø
40 1 L.H. axle bracket Inj. moulded plastic Ready made
41 1 R.H. axle bracket Inj. moulded plastic Ready made
42 1 Allen key Metal 2.5 mm A/F
43 2 Undercarriage support screw Metal 2.2 x 6.5 mm
To Next Page
Loading...
Need help?
General