Part No. Description Material Dimensions
No. off
1 1 Building instructions A4 format
2 1 Name placard - decor set, sheet 1 Printed film Ready made
3 1 Name placard - decor set, sheet 2 Printed film Ready made
Fuselage
10 1 Fuselage Moulded styrofoam Ready made
11 1 Canopy Moulded styrofoam Ready made
12 1 Landing skid - self-adhesive film Clear film Ready made
Wings
20 1 L.H. wing panel and motor nacelle Moulded styrofoam Ready made
21 1 R.H. wing panel and motor nacelle Moulded styrofoam Ready made
22 2 In-fill piece for motor nacelles Moulded styrofoam Ready made
23 1 L.H. aileron Moulded styrofoam Ready made
24 1 R.H. aileron Moulded styrofoam Ready made
25 1 Wing fairing Vac. formed plastic Ready made
Tail panels
30 1 Tailplane Moulded styrofoam Ready made
31 1 Elevator Moulded styrofoam Ready made
32 1 Fin Moulded styrofoam Ready made
33 1 Rudder Moulded styrofoam Ready made
34 1 Fin strake Moulded styrofoam Ready made
Accessories
40 10 Hinge Plastic Ready made
41 4 Glue-in horn Plastic Ready made
42 2 Aileron pushrod, one Z-bend Metal Ready made
43 4 Pushrod connector Metal Ready made
44 4 Socket-head cap screw, pushrod connector Steel M3 x 3 mm
45 4 M2 washer Steel Ready made
46 4 Self-locking nut Steel M2
47 1 Thread-cutting screw Steel M4 x 20 mm
48 1 Allen key Metal 1.5 mm A/F
49 2 Screw hook Metal Ready made
50 1 Rubber band Rubber Ready made
51 3 Velcro tape, hook Plastic 25 x 60 mm
52 3 Velcro tape, loop Plastic 25 x 60 mm
53 1 Front wing retainer screw Plastic M4 x 40 mm
54 1 Rear wing retainer screw Plastic M4 x 25 mm
Wooden parts
60 1 Front spar (2 strips - short) Obechi Ready made
61 1 Rear spar (2 strips - long) Balsa Ready made
62 1 Wing retainer plate, front top Plywood Die-cut, 3 mm
63 1 Wing retainer plate, front bottom Plywood Die-cut, 3 mm
64 3 Wing retainer plate, rear top Plywood Die-cut, 3 mm
65 1 Wing retainer plate, rear bottom Balsa 10 x 12 x 28 mm
66 1 Reinforcing former Plywood Die-cut, 3 mm
67 1 Canopy plate Plywood Die-cut, 3 mm
68 2 Screw hook block Balsa 8 x 8 x 10 mm
69 2 Servo rail Balsa 10 x 12 x 52 mm
70 2 Servo rail Plywood Die-cut, 3 mm
71 2 Hole reinforcement Plywood Die-cut, 3 mm
Wire and tube
80 1 Bowden cable outer, rudder Plastic 3 / 2 Ø x 320 mm
81 1 Bowden cable outer, elevator Plastic 3 / 2 Ø x 480 mm
82 1 Pre-formed rudder pushrod (Z-bend) Steel 1.3 Ø x 510 mm
83 1 Pre-formed elevator pushrod (Z-bend) Steel 1.3 Ø x 560 mm
Power set
90 2 Electric motor Permax 400 Ready made
91 2 Propeller Plastic 125 x 110 mm
92 1 Power system cable set Plastic / metal Ready made
MULTIPLEX Modellsport GmbH & Co KG
Neuer Weg 2
D-75223 Niefern
To Previous Page
Loading...
Need help?
General