MULTISPAN MS-1248U - User Manual

www.multispanindia.com
Page-1
MS-1248U
TechnicalSpecification
UPPER:4Digit7seg0.70,redLEDDisplay
LOWER:3Digit7seg0.50,greenLEDDisplay
J:0To600°C/K:0TO1200°C/PT-100:
-99To400°C/PT.1:-99.0To400.0°C
Output
PowerSupply
Operating
Temperature
Relative
Humidity
100to250VAC,50/60Hz,Approx4VA
0°CTo55°C
Upto95%RHNonCondensing
Model
Display
Size(mm)
PanelCutout
Input
Temperature
Range
96(H)X96(W)X50(D)mm
92X92mm
MS-1248
JTYPE,KTYPE,PT-100/3WSelectable
4Relay,(NO-C-NC),1C/O,5A,230VAC/USB

OPERATINGMANUAL
8CHANNELTEMPERATURESCANNER
MS-1248U
Protection
Level

(Asperrequest)
IP-65(Frontside)AsperIS/IEC60529:2001
1)Doallconnectionasshowninconnectiondiagram.
2)Toenterinparametermode,presskeycombinationaspergiveninchart.
Configure:1.Groupingfacility(Maximumgroup-4)
2.Relaymode(high/low/high&low)for1relaypergroup
-HighandLow,High&Tripfor2relaypergroup
3.Scantype(Range0-99sec)
4.Sensorselection(J,K&PT-100)
5.Skiporunskipchannel
6.DpselectionforPT-100/3WOnly
3)Ifneededtoaddoffset,press+together.
Setoffsetforeachchannelifrequired.
Offsetrangewillbe-25°Cto+25°C.


4)Press&HoldKeyforcontinuousscrollingormanualscrolling.
5)Inholdmodeuse&Keytoselectnextchannel.

Procedure
Connection Diagram
- - -- -
-- -
18
14
19
13
20
12
21
11
22
10
23
24
1 2 3 4
5 6 7 8 9
16
17
15
+++
+ + +++
T/C T/C T/CT/CT/C
PT-100/3W
PT-100/3W
PT-100/3W
PT-100/3W
PT-100/3W
T/CT/C T/C
PT-100/3W
PT-100/3W
PT-100/3W
CH-1 CH-4 CH-5CH-3CH-2
CH-6CH-8 CH-7
NC
NC
NC
NC
C
C
C
C
NO
NO
NO
NO
R1 R3 R4R2
~
50/60 Hz
4VA
!
110
250V AC
L
N

Summary

Operating Procedures

Parameter Configuration Steps

Steps for configuring grouping, relay mode, scan type, sensor, skip/unskip, DP.

Offset Setting Procedure

Connection Diagram

Basic Configuration Menu

Basic Configuration Steps

Guide to setting values and hysteresis in the basic configuration menu.

Parameter Menu Navigation and Options

Key Operation Summary

Menu:1 Configuration Options

Configuring scan time, input sensor type, and channel skip/unskip.

Group and Relay Configuration

Menu:2 Group Menu

Configuring the number of channels per group and maximum groups.

Output Relay Select

Selecting relay output modes like High, Low, or High & Low.

Offset Setting

Menu:3 OFFSET Setting

Procedure for adjusting individual channel offset values.

Safety Precautions

General Safety Instructions

Adherence to manual instructions for safe operation and protection.

Electrical Safety Guidelines

Precautions for wiring, handling terminals, and preventing electric shock.

Wiring and Cable Best Practices

Guidelines for wire rating, twisting, cross-section, and compensation wires.

Installation Guidelines

Built-in Type Installation

Installation Debris Prevention

Power Control Installation

Mechanical Installation

Panel Cutout and Unit Fitment

Installation Location Considerations

Terminal Wiring Torque

MULTISPAN MS-1248U Specifications

General

Brand	MULTISPAN
Model	MS-1248U
Category	Scanner
Language	English