NANO NDL 010 User Manual (English)

Questions and Answers:

J
joseph56Aug 1, 2025
Why does my NANO NDL 010 Dryer have poor dew point performance?
- D
  Diana RothAug 1, 2025
  The NANO Dryer may have poor dew point performance due to several reasons. First, check if the inlet pressure is at least 4 bar; if not, adjust the inlet pressure settings. An electrical fault could also be the reason, so ensure the power is on, the dryer front panel is illuminated, and the dryer is cycling correctly. If the desiccant is moist or contaminated, eliminate the source of contamination and change the cartridges, avoiding reuse. Also, ensure the dryer's performance matches the required air consumption and check the inlet air temperature against the technical specifications. Insufficient purge air, which requires adjustment by service personnel, or a blocked exhaust silencer, also requiring service, could be the cause.
T
Tyler ArnoldAug 10, 2025
What to do if my NANO NDL 010 Dryer fails to cycle?
- A
  Aaron ValdezAug 10, 2025
  If your NANO Dryer fails to cycle, several factors could be responsible. Begin by ensuring the controller is powered and check the on-screen column status to confirm it's powering the exhaust valves during normal cyclic operation. Also, insufficient inlet pressure could be the problem, so ensure it is at least 4 bar and adjust the settings if needed. If the dryer fails to depressurize when cycling, the solenoid valve may not be functioning correctly; if the coil has power, replace the valve (a working valve should produce an audible click when energized). Finally, check the inlet air supply in case the outlet flow stops.
R
Richard GeorgeAug 20, 2025
How to fix constant de-pressurization in my NANO Dryer?
- A
  ashleestoneAug 21, 2025
  If the NANO Dryer is in constant de-pressurization mode, try switching it off and restarting it. Make sure the air supply is on before powering the dryer to allow it to initialize before operation. Erratic airflow from the exhaust could also be the cause, indicating a faulty or damaged valve, which requires service.

NANO NDL 010 Specifications

General

Brand	NANO
Model	NDL 010
Category	Dryer
Language	English

Summary

General Information

Document Introduction

Provides factory prescribed procedures for installation, operation, and maintenance of a nano-porous systems compressed air dryer.

Annotations

Defines CAUTIONS for potential damage/unsafe situations and NOTES for important information requiring attention.

Manufacturer's Details

Provides contact information for enquiries to the manufacturer's Head Office.

Warranty Guidelines

Details the 12-month manufacturer's warranty and directs users to the website for further information.

Packaging

Describes how dryers are packaged, including support cushions, stacking, and damage handling procedures.

Dryer Contents

Lists the items included with the heatless desiccant air dryer, including the dryer itself, packaging, cables, stand components, and documentation.

Technical Description

General Safety

Intended Use of the Dryer

Specifies the dryer's exclusive use for compressed air and operating pressure limits (4-12 barg), warning against modifications.

Personnel

States that only authorised and qualified personnel are permitted to work on the dryer, and the manual is for reference.

Safe Handling

Advises following national safe handling procedures and using lifting aids to minimize risks during lifting or moving.

Installation & Operation

Typical Installation

Illustrates the basic setup of the dryer, including inlet filtration requirements for specified air quality.

Site Selection

Outlines essential conditions for selecting an installation site, such as weather protection, temperature, level surface, and space for access.

Dryer Start-up

Details the electrical connections for compressor eco mode, power supply, pipework, and the initial start-up sequence and display indications.

Monitoring Dryer Performance (Energy Saving Option)

Explains how to monitor dew-point and energy-saving modes, including alarm conditions and control panel indicators.

Shutdown Procedure

Provides step-by-step instructions for safely switching off and depressurizing the dryer, including isolating power and air sources.

Maintenance

Maintenance Guidelines

Lists crucial guidelines for maintenance, including shut down, depressurizing, careful connection handling, and using approved parts.

Daily Checks

Describes essential daily visual and functional checks, including looking for damage, cleaning, and monitoring the dewpoint sensor.

Dryer Service

Recommends a full product service every 2 years or 12,000 hours of operation, mentioning the availability of service kits.

Troubleshooting

Reference to Known Misuse

Lists common operational errors and misuse cases, such as opening valves too quickly, incorrect pipework, electrical issues, and improper component use.