Naturally Filtered MG-10 - User Manual

2
Blue arrows indicate water flow through MG-10.
KDF Mediaguard
®
– an oxidative mineral
which reduces chlorine
and chloramines and
improves carbon life.
Valve Controller
5600-SXT
– regulates the MG-10’s
regeneration frequency
and duration.
Stainless Steel
Activated Carbon
– reduces harmful
chemicals such
as chlorine and
chloramines, as well
as trihalomethanes
(THMs), volatile
organics (VOCs), dirt,
rust, lead, sediment,
foreign odors, and
taste.
Filter Sand
Filter Gravel
Garnet
MG-10 Cutaway
Congratulations on your purchase of the Natural Home MG-10 home
filtration system. The MG-10 is designed to offer the best point-of-entry filtra-
tion performance for homes and small businesses, effectively reducing a broad
spectrum of contaminants.
Please review this guide carefully and give a copy to your licensed plumber
before they arrive to install your system. You should keep this guide for refer-
ence as it will assist you with testing, programming, or troubleshooting your unit
in the future if necessary.
Protects your family by reducing chlorine, chloramines, volatile
organic compounds (VOCs), THMs, and heavy metals
Pure, safe, natural-tasting water
A spa experience in every bath or shower
1
Specifications
Media Carbon: 1 Ft
3
GAC & Centaur mix
KDF: Mediaguard
TM
with four parallel KDF55 stages
Bed: Filter Sand, Mixed Garnet, and Filter Gravel
Flow Rate 10 gallons (38 liters) per minute @ 50 psi inlet
Water Pressure 40 - 100 psi (2.76 bar - 6.895 bar)
Dimensions 11" (27.9cm) diameter x 56" (142.2cm) high
Connections Inlet/Outlet 1" (25.4mm) male NPT
Drain
1
/
2
" (12.7mm) barbed fitting
Weight 130 lbs. (59 kg)
Operating Temperature 40
o
– 150
o
F (4.4
o
– 66
o
C) Warning: Do not allow
exposure to freezing temperatures
Construction Polished stainless steel tank
Controller Valve FLECK Programmable 5600SXT 110 Volts
System Requirements
Water Source Engineered for use with potable, municipally treated
water only. Water source must produce a minimum of
5 gpm at 35 psi for proper regeneration.
Congratulations

Summary

Congratulations on Your MG-10 System

Key Product Benefits

Reduces contaminants like chlorine, VOCs, and heavy metals for pure, safe water.

MG-10 System Specifications

Details media, flow rate, pressure, dimensions, connections, weight, and construction.

MG-10 System Requirements

Specifies potable water source and minimum flow rate for proper regeneration.

Installation Checklist and Parts

Required Parts Checklist

Lists essential components for the bypass valve assembly, including adapters and couplings.

Bypass Valve Assembly Steps

Step-by-step guide to assembling the bypass valve, connecting various parts and securing them.

Important Installation Notes

Covers water testing, shutoff systems, drainage, pressure, existing plumbing, and electrical codes.

MG-10 Control Valve Programming Guide

Control Valve Operation Details

Explains normal operation, power failure recovery, and manual regeneration procedures.

Entering Programming Mode

Steps to enter programming mode by adjusting time and pressing specific buttons.

General Programming Mode Instructions

Instructions for adjusting settings using Up/Down arrows and Extra Cycle button.

Key Programming Settings

Guides through setting display format, valve type, control type, day override, regeneration time, and rinse durations.

Installation and Testing Procedures

MG-10 System Installation Steps

Covers locating a suitable spot, shutting off water, connecting the bypass valve and drain line.

Post-Installation System Testing

Procedures to check for leaks, run regeneration cycles, and verify media flushing.

Control Valve Operation and Troubleshooting

Control Valve Operational Notes

Explains normal operation, power failure response, and regeneration display.

Troubleshooting Water Pressure Issues

Guides on diagnosing and resolving water pressure problems by using the bypass manifold.

Critical Safety and Liability Warnings

Details risks of leaks, property damage, freezing, and recommends leak detection systems.

3-Year Limited Warranty Information

Warranty Coverage Details

Covers defects in materials and workmanship for three years when installed by a licensed plumber.

Warranty Exclusions and Limitations

Excludes failures due to water quality, misuse, accident, leaks, unauthorized modifications, and improper installation.

How to Obtain Warranty Service

Contact Customer Service with detailed problem description for repair or replacement.

Naturally Filtered MG-10 Specifications

General

Brand	Naturally Filtered
Model	MG-10
Category	Water Filtration Systems
Language	English