Navico B&G V100-B User Manual (English)

Questions and Answers:

U
uramseyAug 17, 2025
How to fix Navico B&G V100-B Receiver that won't power on?
- H
  hoffmanmichelleAug 17, 2025
  If your Navico Receiver won't power on, there are several potential causes. First, check the blade fuse in the blackbox to ensure it has the correct amperage (10A) and reset the circuit breaker. Also, verify that the fuse/breaker rating at the fuse/breaker panel is correct. Damaged or corroded wiring could also be the culprit, so inspect the wiring. Finally, remember that the system can only be turned on from a fixed handset by short pressing the power button.
C
Cody McleanAug 20, 2025
Why does my Navico B&G V100-B Receiver system shut down when transmitting?
- N
  Nicholas BarrettAug 20, 2025
  If your Navico Receiver system shuts down when transmitting, it may be due to insufficient power available at the blackbox power terminals or a flat battery. A built-in low voltage safety feature shuts down the system when the supply voltage drops below the specified value, which is likely to occur when the VHF is transmitting at HI (25W) power. Ensure the wiring is capable of supplying the required current.
J
Jay RichardsAug 22, 2025
What to do if AIS won't TX on Navico Receiver?
- B
  Barbara BeltranAug 22, 2025
  If your Navico Receiver's AIS won't transmit, first ensure a VHF antenna is connected to the AIS antenna port. All details in the AIS setup screen must be completed, including a valid MMSI. A GPS fix must be obtained. Also, check that the Silent Switch is OFF, as the AIS system will only receive but not transmit while Silent mode is active.
K
Kevin MartinezAug 25, 2025
Why can I TX but don’t hear a response on my Navico B&G V100-B?
- M
  Mark MontgomeryAug 26, 2025
  If you can transmit with your Navico Receiver but don’t hear a response, ensure a Simplex channel is used for radio-to-radio communications. Adjust the squelch so that noise just clears. If the channel is set to LO (1W) power, change to HI (25W) power where available by long pressing the OK key. Also, check the VHF antenna and test with a known good antenna.
D
David EvansAug 27, 2025
What causes repeated blown fuse or circuit breaker tripping in Navico B&G V100-B?
- E
  ecooperAug 27, 2025
  If you are experiencing a repeated blown fuse or circuit breaker tripping with your Navico Receiver, check the wiring to ensure the power (+) is connected to the battery (+), as wiring reverse polarity could be the cause.
C
Caroline TerrellAug 29, 2025
How to fix no sound from Navico B&G V100-B handset speaker?
- A
  Anne GarciaAug 30, 2025
  If there is no sound from your Navico Receiver handset speaker, check that the volume is not set too low and adjust as needed. Also, ensure that the handset speaker is turned ON.
J
James ReedSep 1, 2025
Why can RX but station can’t hear me on Navico B&G V100-B?
- H
  hillmatthewSep 1, 2025
  If you can receive but the station can’t hear you on your Navico Receiver, the channel might be set to LO (1W) power. Try changing to HI (25W) power where available by long pressing the OK key. Also, check the VHF antenna and test with a properly functioning antenna.
B
brentlambSep 4, 2025
How to turn on DSC on Navico Receiver?
- S
  Spencer MartinSep 4, 2025
  If your Navico Receiver shows DSC is off, you must enter a valid MMSI before DSC can be used. Also, check that the DSC function is turned ON.
K
Kristine CooperSep 6, 2025
What to do if Navico B&G V100-B has no GPS fix?
- A
  Ashley GreenSep 6, 2025
  If your Navico Receiver has no GPS fix, check that the GPS Source is set correctly to either Internal or Networked. If using an external GPS antenna, ensure it has a clear view of the sky, as the antenna may be covered or the location may have poor coverage.
C
Caroline ParkerSep 9, 2025
How to turn off ATIS on Navico Receiver?
- D
  Dr. Rachel YuSep 9, 2025
  If your Navico Receiver is showing ATIS is ON, the ATIS function must be turned OFF, as ATIS and DSC cannot be ON at the same time.