Navico Simrad RS100 User Manual (English)

Questions and Answers:

D
Dominic PerezAug 18, 2025
How to fix Navico Simrad RS100 Receiver that won't power on?
- D
  Donald MeltonAug 18, 2025
  If your Navico Receiver won't power on, there are several potential causes. First, check the blade fuse in the blackbox to ensure it has the correct amperage (10A) and reset the circuit breaker. Also, verify that the fuse/breaker rating at the fuse/breaker panel is correct. Damaged or corroded wiring could also be the culprit, so inspect the wiring. Finally, remember that the system can only be turned on from a fixed handset by short pressing the power button.
B
Barbara SmithAug 20, 2025
Why does my Navico Receiver system shut down when transmitting?
- D
  David BrownAug 20, 2025
  If your Navico Receiver system shuts down when transmitting, it may be due to insufficient power available at the blackbox power terminals or a flat battery. A built-in low voltage safety feature shuts down the system when the supply voltage drops below the specified value, which is likely to occur when the VHF is transmitting at HI (25W) power. Ensure the wiring is capable of supplying the required current.
A
Angela BauerAug 23, 2025
What to do if AIS won't TX on Navico Receiver?
- H
  harrisedwardAug 23, 2025
  If your Navico Receiver's AIS won't transmit, first ensure a VHF antenna is connected to the AIS antenna port. All details in the AIS setup screen must be completed, including a valid MMSI. A GPS fix must be obtained. Also, check that the Silent Switch is OFF, as the AIS system will only receive but not transmit while Silent mode is active.
P
Patrick WaltersAug 26, 2025
Why can I TX but don’t hear a response on my Navico Receiver?
- A
  Antonio PerezAug 26, 2025
  If you can transmit with your Navico Receiver but don’t hear a response, ensure a Simplex channel is used for radio-to-radio communications. Adjust the squelch so that noise just clears. If the channel is set to LO (1W) power, change to HI (25W) power where available by long pressing the OK key. Also, check the VHF antenna and test with a known good antenna.
K
Kristin GuzmanAug 27, 2025
What causes repeated blown fuse or circuit breaker tripping in Navico Simrad RS100 Receiver?
- J
  Jill ObrienAug 27, 2025
  If you are experiencing a repeated blown fuse or circuit breaker tripping with your Navico Receiver, check the wiring to ensure the power (+) is connected to the battery (+), as wiring reverse polarity could be the cause.
W
washingtonjaneAug 30, 2025
How to fix no sound from Navico Receiver handset speaker?
- J
  Judith MolinaAug 30, 2025
  If there is no sound from your Navico Receiver handset speaker, check that the volume is not set too low and adjust as needed. Also, ensure that the handset speaker is turned ON.
F
Frank TaylorSep 1, 2025
Why can RX but station can’t hear me on Navico Simrad RS100?
- J
  Jenny DennisSep 2, 2025
  If you can receive but the station can’t hear you on your Navico Receiver, the channel might be set to LO (1W) power. Try changing to HI (25W) power where available by long pressing the OK key. Also, check the VHF antenna and test with a properly functioning antenna.
B
blackbenjaminSep 4, 2025
How to turn on DSC on Navico Simrad RS100?
- S
  smithcarlaSep 4, 2025
  If your Navico Receiver shows DSC is off, you must enter a valid MMSI before DSC can be used. Also, check that the DSC function is turned ON.
M
mike45Sep 6, 2025
What to do if Navico Simrad RS100 has no GPS fix?
- G
  Glenn WangSep 7, 2025
  If your Navico Receiver has no GPS fix, check that the GPS Source is set correctly to either Internal or Networked. If using an external GPS antenna, ensure it has a clear view of the sky, as the antenna may be covered or the location may have poor coverage.
S
Stephen ColeSep 9, 2025
How to turn off ATIS on Navico Simrad RS100?
- B
  baldwintaylorSep 9, 2025
  If your Navico Receiver is showing ATIS is ON, the ATIS function must be turned OFF, as ATIS and DSC cannot be ON at the same time.

Navico Simrad RS100 Specifications

General

Brand	Navico
Model	Simrad RS100
Category	Receiver
Language	English

Summary

Preface

Disclaimer

Legal disclaimers regarding product use and liability.

Governing Language

Specifies the official language version of the documentation.

Copyright

Warranty

Information about the product's warranty.

About this manual

Describes the manual's purpose and scope.

Blackbox VHF radio system

Lists the products and components covered by the manual.

Compliance and Notices

EU RF Exposure Compliance

Notice regarding RF exposure limits for fixed mount VHF devices.

US FCC Compliance

FCC rules compliance for device operation.

RF Emissions Notice

Information on RF emissions and installation requirements.

Canadian and ISED Compliance

Canadian Compliance Statements

Device compliance with Canadian ICES and RSS standards.

ISED Compliance Statements

RF exposure limits compliance with ISED regulations.

System Functions Overview

Digital Selective Calling (DSC)

Explains the benefits and functionality of DSC.

Automatic Transmitter Identification System (ATIS)

Details ATIS requirements for inland waterways.

AIS and Customer Information

MMSI and ATIS ID Details

Information on Marine Mobile Service Identity and ATIS ID numbers.

AIS Class-B Safety Warning

Safety warning regarding the use of AIS as a navigation aid.

General Information

RS100/V100 System Features

Lists features of the RS100/V100 system.

RS100-B/V100-B Additional Features

Highlights features specific to the RS100-B/V100-B model.

Displaying and Navigating Menus

Explains how to navigate the radio's menu system.

LCD Symbols and Meanings

LCD Symbol Descriptions

Defines icons displayed on the radio's LCD screen.

LCD Functions

Screen Display Indicators

Details the various symbols and their functions on the display.

Keypad Functions

Distress and Channel Selection Keys

Details functions of Distress, 16/9, and channel keys.

Power and Menu Navigation Keys

Explains the X/POWER and OK/HL keys for navigation.

More Keypad Functions

Channel Up/Down and Volume/Squelch

Explains channel selection and volume/squelch adjustment.

Menu Access and Scan/TRI Keys

Details keys for menu access, scanning, and TRI watch.

Additional Keypad Functions

MOB and Recorder Keys

Explains keys for Man Over Board and Voice Recorder.

LCD and Alpha Numeric Keypad

Refers to the display and the alphanumeric input method.

Wired Handset Numeric Keys

Numeric Key Functions by Mode

Details key functions based on radio mode (Normal, Data Input, Intercom).

Radio Menus

Menu Tree Structure

Outlines the available menus and submenus.

Scan Menu Options

All Scan Modes

Describes different scan modes like All Scan and My Channels.

Watch and Voice Recorder Menus

Watch Mode Configuration

Details Dual Watch, Tri Watch, and setting watch channels.

Voice Recorder Operation

Explains how to use the voice recorder feature.

Display and Backlight Settings

Screen Display Options

Settings for Time, Position, and COG/SOG displays.

Backlight and Network Configuration

Adjusting backlight and synchronizing with NMEA 2000 network.

Radio Setup Options

Sensitivity and Channel Settings

Adjusting receiver sensitivity and selecting channel banks.

Power Output and Key Beeps

Settings for transmission power and key beep volume.

Units, Speaker, and GPS Settings

Unit and Speaker Configurations

Setting units (speed, course) and configuring speakers.

Manual GPS Entry

Procedure for manually entering GPS position data.

GPS Source and Communication Settings

GPS Source Selection

Choosing between Networked or Internal GPS sources.

COM Port and Baud Rate

Configuring COM port for NMEA data and setting baud rate.

Time, Call Sign, and DSC/ATIS Setup

Time and Vessel Call Sign Settings

Setting time offset, format, and vessel call sign.

DSC/ATIS Function Enablement

Enabling DSC or ATIS functions based on region.

DSC/ATIS Advanced Settings

Acknowledgement and Auto Switch Settings

Configuring auto-acknowledgements and channel switching for DSC calls.

DSC Timeout and AIS Setup

DSC Timeout Configuration

Setting inactivity timeouts for DSC calls.

AIS Setup Options

Configuring AIS function, silent mode, and display.

Alarms and Vessel Details

Alarm System Overview

Overview of audible and visual alerts for critical functions.

Viewing AIS Vessel Details

How to view saved AIS static data.

Specific Alert Configurations

GPS, WX, and DSC Alarms

Configuring GPS, WX, and DSC alarm volumes and screen flashes.

T/CPA Alarms

Settings for Time to Closest Point of Approach alarms.

Handsets Overview

Handset Types and Pairing

Details on fixed and wireless handsets, and pairing process.

Wireless Handset Management

Pairing and Removing Wireless Handsets

Steps to pair, remove, and locate wireless handsets.

Wireless Handset Audio Configuration

Options for repeating audio between handset and host.

Diagnostics

GPS Status Diagnostics

Displays status of the internal GPS system.

System Diagnostics

Views radio, DSC, and handset system diagnostics.

Advanced Diagnostics

NMEA2000 and AIS Diagnostics

Displays NMEA2000 network status and AIS diagnostics.

Reset Functions

Region and Country Settings

How to change the radio's region and country settings.

Factory Reset Procedure

Restores radio settings to factory defaults.

DSC Call Menu

DSC Calls Overview

Explains the purpose and types of DSC calls.

Individual and Distress Calls

Procedures for making individual and distress calls.

More DSC Call Procedures

Distress Call Sending

Step-by-step guide for sending a distress call.

Group and All Ships Calls

Procedures for group calls and non-distress announcements.

Track Buddy and DSC Test Calls

Track Buddy Functionality

How to set up and use the Track Buddy feature.

DSC Test Call Procedures

Steps for initiating a DSC test call.

Contacts and Call Logs

Managing Contacts and Groups

Creating, editing, and deleting contacts and groups.

Reviewing Call Logs

Accessing and managing SENT, RECEIVED, and DISTRESS call logs.

AIS Menu (NRS-2 Only)

About AIS and Receiver Function

Introduction to AIS and how the receiver works.

AIS Transmitter and Information Display

Configuring the AIS transmitter and displaying AIS information.

AIS Plotter and T/CPA Alerts

AIS Plotter Symbols and Meanings

Explains symbols used on the AIS plotter screen.

T/CPA Approach Screen Details

Details on the TCPA approach screen and alerts.

Fog Horn, Intercom, and Hailer

Using the Fog Horn

How to activate and select fog horn sounds.

Using the Intercom (IC)

Instructions for using the intercom feature between handsets.

Hailer and Announce Functions

Using the Hailer

How to use the hailer for high-volume announcements.

Using the Announce Function

How to make immediate announcements to all stations.

My Channels

Managing Favorite Channels

Creating custom channel lists for quick access.

Shortcuts

Adding and Editing Shortcuts

Customizing the shortcuts menu.

MOB and NAV Functions

Man Over Board (MOB) Operation

How to activate and use the MOB function.

Navigation Function (NAV)

Installation Guide

What's in the Box

Lists all items included in the product package.

Component Lists

Details the items supplied with the Blackbox, Handset, and Speaker.

Installation Guidelines

Mounting Guidelines

Recommendations for choosing mounting locations and avoiding interference.

Mounting the Blackbox

Mounting the CR100 Fixed Handset Cradle

Mounting the BC-12 Wireless Handset Cradle

Mounting the Speaker

Flush Mounting Procedure

Steps for flush mounting the speaker.

Speaker Surface Mounting

Mounting the GPS-500 Antenna

Pole and Hard Surface Mounting

Guidance for mounting the GPS antenna on poles or surfaces.

Wiring Guidelines and Connectors

Wiring Do's and Don'ts

Best practices and warnings for cable routing and connections.

Blackbox Connector Details

Information on accessing and identifying Blackbox connectors.

Cable Grommets

Connector Pinouts

GND, Fuse, Power, and Speaker Connections

Pin details for power, speaker, and ground connections.

Handset and HS2-4 Connections

Pin details for handset connections.

AUX and HAILER Connections

AUXiliary Connections

Pin assignments for NMEA 0183, Horn, and AIS Silent Switch.

HAILER Speaker Connection

Wiring details for the hailer speaker.

Plug-in Connections Overview

Summary of the Blackbox's plug-in connection ports.

Wiring Diagram

First Time Startup Configuration

Country and MMSI Setup

Initial selection of country mode and entry of MMSI.

ATIS ID, Call Sign, and GPS Source

Configuring ATIS, call sign, and GPS source during startup.

VHF Radio Help and Troubleshooting

Software Updates and Factory Reset

Information on updating software and performing a factory reset.

Power and AIS LED Indicators

Explains the meaning of power and AIS LED status lights.

System Troubleshooting

Power and Sound Issues

Solutions for power-on problems and lack of sound.

Wiring and Power Supply Issues

Troubleshooting wiring, fuses, and voltage supply.

VHF Troubleshooting

TX/RX and Squelch Issues

Resolving problems with transmitting, receiving, or squelch.

Power Level and Antenna Issues

Addressing reduced transmit power and antenna-related problems.

AIS and DSC/ATIS Troubleshooting

AIS Transmission Issues

Solutions for problems with AIS transmission.

DSC/ATIS Functionality Issues

Resolving issues related to DSC or ATIS function.

RS100/B, V100/B Specifications

System Features and Technical Data

Overview of system features and general technical parameters.

VHF Transceiver Specifications

VHF Transmitter and Receiver Details

Technical specifications for the VHF transmitter and receiver.

AIS (Class-B) Specifications

Detailed specifications for the AIS Class-B system.

GPS, Wireless, and Handset Specifications

Built-in GPS and Wireless Specs

Technical details for the GPS receiver and wireless communication.

Handset and Cradle Charger Specs

Specifications for handsets and their charging cradle.

Channel Charts

EU and International Channel Chart

Channel assignments and frequencies for EU and international use.

EU and International Channel Chart Details

Channel Notes and References

Explanations and notes related to the channel chart data.

USA Channel Chart

USA Weather Channels

List of weather channels available in the USA.

EAS Event Codes

Codes for Emergency Alert System events.

EAS Event Codes and Naming Conventions

Canada Channel Chart

Canada Weather Channels

List of weather channels available in Canada.

Dimensional Drawings

Blackbox and Fixed Handset Dimensions

Dimensions for the Blackbox and fixed handsets.

Speaker and Cradle Dimensions

Wireless Handset Dimensions

Appendix

Country Settings Table

Table mapping regions to countries for radio settings.

NMEA 2000 Compliant PGN List

Related product manuals

Navico B&G V100-B

87 pages

Navico Simrad RS100 User Manual

Table of Contents