NETGEAR XS512EM Installation

Installation
Package Contents
Unpack the box and verify the contents:
• Switch model XS512EM or XS724EM
• Power cord (localized to the country of sale)
• Four rubber footpads for tabletop installation
• Rack-mount kit
• Installation guide
XS724EM
NETGEAR Smart Managed Plus
12-Port 10-Gigabit/Multi-Gigabit Ethernet Switch with 2 SFP+
Combo Ports (XS512EM)
24-Port 10-Gigabit/Multi-Gigabit Ethernet Switch with 2 SFP+
Combo Ports (XS724EM)
SFP+
LED
SFP+
LED
XS512EM
Connect the Switch to Your Network
For Gigabit connections, use Category 5e (Cat 5e) or higher-rated Ethernet
cables terminated with RJ-45 connectors. To use an SFP+ port, you must
insert either a 10G SFP+ or 1G SFP transceiver module, which is available from
NETGEAR.
Step 1. Connect the equipment.
Step 2. Connect power.
Network router
Internet
XS724EM
switch
GS110E M X
switches
2.5G link
to AP
Sample Connections
Step 3. Check the status.
Power LED Ethernet port LEDs
On
O
10G link (both port LEDs on). Both port LEDs blinking
indicates trac activity.
Fan LED
5G link (le port LED o, right port LED on). Right
port LED blinking indicates trac activity.
Check fan
Normal
2.5G link (le port LED on, right port LED o). Le
port LED blinking indicates trac activity.
1G or 100M link (both port LEDs on). Both port LEDs
blinking indicates trac activity.
No link (both port LEDs o).
SFP port LEDs (round)
10G link (both port LEDs on). Both port LEDs blinking
indicates trac activity.
1G link (both port LEDs on). Both port LEDs blinking
indicates trac activity.
No link (both port LEDs o).
Note: The combo ports let you establish a 1G or 10G connection on either the
Ethernet RJ-45 port or the SFP+ port. You cannot use both the RJ-45 and SPF+
ports simultaneously.
Cables and Speeds
The following table describes the network cables that you can use for the switch
connections and the speeds that these cables can support, up to 328 feet (100
meters).
10G link
to 10G NAS
10G link to computer
with a Thunderbolt port
1G link to
computer
2.5G link to
2.5G gaming
computer
(Continued on the next page)
1G link
to AP

NETGEAR XS512EM Specifications

General

Switch type	Managed
Switch layer	L2
Quality of Service (QoS) support	Yes
Stackable	-
Form factor	1U
Certification	47 CFR FCC, ICES-003:2016, ANSI C63.4:2014, EN55032:2012+AC:2013, EN 55024:2010, EN 61000-3-2:2014, EN 6100-3-3:2013, AS/NZS CISPR 32:2013, VCCI-CISPR32:2016, CNS 13438, IEC 60950-1:2005(ed.2) + A1:2009 + A2:2013, UL 60950-1, EN 60950-1: 2006 + A11:2009 + A1:2010 + A12:2011 + A2:2013, IEC 60950-1:2005 (ed.2)+A1:2009+A2:2013, AS/NZS 60950.1:2015 CNS14336-1
Product color	Blue, Grey
Number of fans	2 fan(s)
Power connector	DC-in jack
SFP+ module slots quantity	2
Basic switching RJ-45 Ethernet ports type	10G Ethernet (100/1000/10000)
Basic switching RJ-45 Ethernet ports quantity	12
Jumbo frames	9000
MAC address table	32000 entries
Packet buffer memory	3 MB
Mean time between failures (MTBF)	1113477 h
Number of VLANs	64
Networking standards	IEEE 802.1Q, IEEE 802.1p, IEEE 802.3, IEEE 802.3ab, IEEE 802.3ae, IEEE 802.3an, IEEE 802.3az, IEEE 802.3bz, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z
Virtual LAN features	Port-based VLAN
Input current	2 A
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
DHCP features	DHCP client
Sustainability certificates	ENERGY STAR
Heat dissipation	261.38 BTU/h
Storage temperature (T-T)	-20 - 70 °C
Operating temperature (T-T)	0 - 50 °C
Storage relative humidity (H-H)	0 - 95 %
Operating relative humidity (H-H)	0 - 90 %
Harmonized System (HS) code	85176990

Weight and Dimensions

Depth	204 mm
Width	328 mm
Height	43 mm
Weight	2510 g