New Holland B110C Service Manual

31 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

B100C / B100CLR / B100CTC

B110C / B110CTC / B115C

Print No. 84568042A

Backhoe Loaders

SERVICE MANUAL

Other manuals for New Holland B110C

Original Instructions476 pages

Operator's Manual374 pages

Questions and Answers:

V
Victoria MillerAug 25, 2025
Why is my New Holland Front End Loaders engine overheating?
- B
  Bradley WilsonAug 25, 2025
  If the New Holland Front End Loaders engine overheats, it could be due to several reasons. The centrifugal pump of the cooling system might be faulty and require overhaul or replacement. A faulty temperature switch can also cause overheating, so replace it. The radiator may be partially faulty due to scales or leaks, requiring washing and repair. Scales in the coolant passage compartments can also cause overheating, so clean them carefully. Other potential causes include a slack centrifugal pump drive belt or fan drive belt, needing adjustment, or insufficient coolant, requiring you to restore the level in the expansion tank. Incorrect engine timing or a restricted air filter can also lead to overheating; check and correct the timing, and clean or replace the air filter element.
C
Charles ColemanAug 25, 2025
What to do if my New Holland B110C engine suddenly stops?
- A
  Adam BryantAug 26, 2025
  If the New Holland Front End Loaders engine stops, there could be several reasons. An irregular delivery from the supply pump could be the cause, so check the delivery on the workbench. Dirt or water accumulations in the fuel lines can also cause the engine to stop; disconnect the lines and the injection pump and carefully clean them, also clean and dry the fuel tank if needed. Restricted fuel filters can also be the issue, so replace the filter cartridges. Burned or cracked valves may also cause the engine to stop, so replace the valves. Air in the fuel system can also cause this; check the lines, fittings, supply pump, filters, and injection pump for air, then bleed the system. Lastly, damaged injection pump controls can cause the engine to stop, so replace the damaged parts.
M
Mark HinesAug 31, 2025
What to do if the starter motor of my New Holland B110C does not run?
- J
  Jeremy KhanAug 31, 2025
  If the New Holland Front End Loaders starter motor does not run, several issues could be the cause. Too low specific density and battery level can prevent the starter motor from running; inspect the battery. A poor ignition switch circuit connection or contact can also be the issue; replace the wiring harness and the ignition switch. Malfunction of the coil or of the magnetic switch pull-in cylinder can also prevent the starter motor from running; replace the magnetic switch.
A
Angela HallSep 1, 2025
Why is the lifting circuit of my New Holland B110C Front End Loaders failing to operate properly?
- W
  wkochSep 1, 2025
  If the New Holland Front End Loaders lifting circuit fails to operate, is slow, or loses power, a leaking valve spool could be the cause. Inspect the spool and check it for wear or scratches. Alternatively, leaking cylinder seals or a damaged cylinder barrel could be the issue. Inspect and reseal the cylinder in this case.
A
Amanda DavisSep 2, 2025
Why is the bucket of my New Holland Front End Loaders not operating correctly?
- S
  Stephanie RomeroSep 2, 2025
  If the New Holland Front End Loaders bucket fails to operate, is slow, or loses power, it could be due to several reasons. The relief valves being stuck open, set to a too low value, or a leak in the seat can cause this; check the bucket circuit relief valve. A leaking valve spool can also cause this; inspect the spool and check it for wear or scratches. Leaking cylinder seals or a damaged cylinder barrel can also be the issue; inspect and reseal the cylinder.
M
megan29Sep 3, 2025
Why is the electrical system of my New Holland Front End Loaders inoperative?
- B
  Brianna ChristensenSep 3, 2025
  If the New Holland Front End Loaders electrical system is inoperative, several issues could be the cause. Loose or oxidised battery connections can cause this; check that the battery voltage with open circuit is at least 12.6 V. Sulphated batteries can also be the issue; check the electrolyte level and density. A battery isolator switch being off can also cause this; restore the battery isolator switch. The main connection fuse of the machine being blown can also cause the electrical system to be inoperative; find the reason of the failure and replace the connection fuse.
R
runderwoodSep 5, 2025
Why can't my New Holland B110C starter motor crank the engine?
- K
  Kenneth AndrewsSep 5, 2025
  If the New Holland Front End Loaders starter motor running cannot crank the engine, it could be due to the pinion gear not engaging with the ring gear. In this case, repair or replace the clutch and the control lever. Another possible cause is a sliding clutch, which would require replacing the clutch.
M
Michael McknightSep 6, 2025
What causes the pinion gear to spring in my New Holland B110C Front End Loaders?
- K
  Kimberly AndersonSep 6, 2025
  If the pinion gear of your New Holland Front End Loaders springs, it could be due to poor ignition switch return, in which case you should replace the ignition switch. It could also be caused by field coil loss or a burnt magnetic switch coil, etc., indicating a pinion gear disengagement fault caused by a coil short circuit in the magnetic switch.
L
Lindsey DelacruzSep 7, 2025
What to do if my New Holland B110C Front End Loaders is not recharging?
- C
  Casey CampbellSep 7, 2025
  If the New Holland Front End Loaders is not recharged, it could be due to a recharge circuit interruption (warning lamp, fuse, connector, etc.). Check the connections of the recharge circuit and clean and tighten the alternator and battery terminals. It could also be due to an inefficient voltage regulator, a rotor winder interruption or worn brushes, in which case you should replace the alternator.
D
David HuntSep 8, 2025
Why is my New Holland B110C Front End Loaders recharge insufficient?
- L
  Larry JohnsonSep 8, 2025
  If the New Holland Front End Loaders recharge is insufficient, it could be due to a slackened fan belt, so supply the correct tension. It could also be due to a faulty voltage regulator, excessive wear of rotor rings or brushes, short-circuited diodes, or short-circuited stator winders or rotor winder, in which case you should replace the alternator.

New Holland B110C Specifications

General

Engine Power	110 hp
Max. Travel Speed	40 km/h
Loader Capacity	1.0 cu. m
Max Lift Height	3.4 m
Bucket Capacity	1.0 cu. m

Related product manuals

New Holland B110

New Holland B115B

Preview: New Holland B100C

New Holland B100C

Preview: New Holland B80B

New Holland B80B

Preview: New Holland B90B

New Holland B90B

Preview: New Holland B95CTC

New Holland B95CTC

Preview: New Holland B90BLR

New Holland B90BLR

New Holland LB115.B 4WS

New Holland L865

New Holland Lx885

Preview: New Holland W190D

New Holland W190D

New Holland 611TL