New Holland BC5000 Series
Small Square Baler Specifications
BC5050 BC5060 BC5070 BC5080
Page 1 of 2
MODEL BC5050 BC5060 BC5070 BC5080
B
ALE SIZE:
Cross section, in. (cm) 14x18 (36x46) 14x18 (36x46) 14x18 (36x46) 16x18 (41x48)
Length, in. (cm) ................................................................................Adjustable, 12 to 52 (31 to 132) ..............................................................................
SUPER-SWEEP PICKUP:
Width inside, in. (m) 65 (1.65) 65 (1.65) 75 (1.9) 75 (1.9)
Width on flare, in. (m) 70 (1.8) 70 (1.8) 80 (2) 80 (2)
Number of teeth 88 on four tooth bars 110 on five tooth bars 156 on six tooth bars 156 on six tooth bars
Floating windguard Eight rods Eight rods Thirteen rods Thirteen rods
Drive ........V-belt to roller chain to “lost motion” reel drive .......... ——
Gauge wheel 3.00x12; semi-pneumatic 3.00x12; semi-pneumatic 15x6.00x6 15x6.00x6
ROTARY FEEDING SYSTEM:
Type — Packer fork in combination Packer fork in combination Packer fork in combination
with two paired rotors with three paired rotors with three paired rotors
Drive — ............................Chain from main drive shaft; sealed ball bearings on all shafts ..........................
FLOW-ACTION
®
FEEDING SYSTEM:
Type Six feeder tines on a moving —— —
finger bar
Drive Chain; sealed ball bearings —— —
FEED OPENING, sq. in. (cm
3
) 283 (1826) 283 (1826) 283 (1826) 318 (2052)
PLUNGER:
Stroke length, in. (cm) 30 (76.2) 30 (76.2) 30 (76.2) 30 (76.2)
Speed (540 rpm) 79 SPM 93 SPM 93 SPM 93 SPM
Construction ..........High-strength steel throughout; modified extension is built into the plunger face, eliminating the need for bolt-on extensions ........
TYING MECHANISMS:
Type Knotter Knotter or twister Knotter or twister (heavy-duty) Knotter (heavy-duty)
Protection Shearbolt Shearbolt Shearbolt Shearbolt
Capacity (twine) Four balls Six balls Eight balls Eight balls
(wire) NA Four coils Four coils NA
MAIN DRIVE:
Flywheel diameter, in. (cm) 22 (56) 22 (56) 22 (56) 22 (56)
PTO Three-joint Three-joint Three-joint Three-joint
Protection ..........................................................................Shearbolt, overrunning and slip clutches ........................................................................
Gearbox ................................................Hypoid with tapered roller bearings; heat-treated alloy steel running in oil ..............................................
TIRES:
Flotation (right) 25x7.50-15, 6PR 27x9.50-15, 6 PR 27x9.50-15, 6PR 11Lx15, 6PR
(left) 27x9.50-15, 6PR 31x13.50-15, 6PR 31x13.50-15, 6PR 14Lx16.1, 6PR
DIMENSIONS:
Height (max.), in. (cm) 58 (146) 70 (178) 71 (180) 71 (180)
Width, in. (cm) 108 (275) 110 (279) 120 (304) 120 (304)
Length:, in. (cm)
With 3-joint PTO and
quarter-turn bale chute 240 (610) 247 (626) 247 (626) 247 (626)
To Next Page
Need help?
General
