Newall DP700 MK2 User Manual

DP700 MK2 Quick Start Guide
Technical Specification
For the complete manual please download from:
http://newall.com , Click Technical Support to access the download page.
Environmental
Operating Temperature Storage Temperature
-10°C to 50°C -20 to 70°C
Environmental Conditions - IP40 (Stand Alone)
IP54 (Panel Mount)
Relative Humidity - maximum 95% for temperature up to 31°C
Disposal
At the end of it’s life, you should dispose of the DP700 in a safe
manner applicable to electronic goods.
The case work is suitable for recycling. Please consult local
regulations on disposal.
DP7001016ENUS
023-81365-UK/0
Connections
Electrical
EU Directive 73/23/EEC (Low Voltage
Directive)
BS EN 55022:1998 Class B
BS EN 55024:1998
Input to Power Supply Unit (Supplied)
100-240V (47-63Hz)
External switch-mode
Output voltage 15VDC
Input Voltage to DP700
15-24VDC ±10%
Conforms to Low Voltage Directive
External PSU Input
AMERICAS
Newall Electronics Inc.
USA
Tel: +1 614 771 0213
CHINA & TAIWAN
Sensata Technologies
China Co., Ltd.
People's Republic of China
Tel: +86 12 2306 1500
SINGAPORE AND KOREA
Sensata Technologies Co., Ltd.
Singapore
Tel: +65 647 86 867
JAPAN
Sensata Technologies Japan Ltd.
Japan
Tel: +81 45 277 7120
For more information about this or any of our products
please contact us at sales@newall.com or visit www.newall.com
Note: Newall Measurements Systems reserves the right to change specifications without notice.
Warnings
The mains supply is connected into a switch mode power supply (separate from your DP700) via a
detachable supply cord supplied. If another supply cord is used, it must have fitted a C5, 10A, EARTHED
mains connector with a cord rated for at least 10A.
If a mains plug is not already fitted to the supply cord or is of the wrong type, then a suitable EARTHED plug
should be used which complies with the relevant specifications for plugs and socket-outlets.
You can only use the DP700 with Newall Spherosyn and Microsyn analogue encoders.
Unit only to be serviced by Newall qualified personnel or authorised alternatives.
Turn off the power by disconnecting the power supply connector before you connect the encoder(s)
Cabinet equipotential terminal
for grounding to machine
Cable Clamp
Encoder Input
Connection
1,2 or 3 According
to Model
RS232 Output

Newall DP700 MK2 Specifications

General

Display Type	LCD
Storage Temperature	-20°C to 70°C
Axes	1, 2 or 3
Resolution	0.5 μm, 1 μm, 5 μm, 10 μm
Operating Temperature	0°C to 50°C
Relative Humidity	90% non-condensing
Display Digits	7 digits
Input Voltage	9-30 VDC

Summary

Safety and Compliance Information

Power Supply and Cord Safety

Requirements for mains supply cords, connectors, and plugs.

Usage and Servicing Guidelines

Specifies compatible encoders, authorized servicing, and power disconnection.

Technical Specifications

Environmental Specifications

Covers operating/storage temperatures, humidity, and conditions.

Electrical Specifications

Lists electrical directives, standards, and voltage inputs/outputs.

Disposal Guidelines

Instructions for safe disposal of the unit at end-of-life.

Hardware Connections Overview

Encoder Input and RS232 Ports

Details on connection points for encoders and RS232 output.

Power and Grounding Connections

Describes DC input, PSU connections, and equipotential terminal.

Keypad and Display Functions

Keypad Layout and Functions

Explains the function of each key on the DP700 keypad.

Axis Selection and Mode Switching

Details on switching between axes and absolute/incremental modes.

Display Unit Switching

Covers switching between Inch and mm display modes.

Axis Zeroing and Presetting

Zeroing an Axis in Zero Mode

Procedure to set an axis to zero in Zero Mode.

Zeroing an Axis in Set Mode

Procedure to set an axis to zero in Set Mode.

Presetting an Axis

Procedure to preset an axis value in Set Mode.

Setup Menu Navigation

Entering the Setup Menu

Steps to access the setup menu using function keys.

Configuring Basic Settings

Guides on setting language, encoder type, resolution, and direction.

Advanced Setup Options

Covers error compensation, plane setup, feed settings, and beeps.

Encoder Matching Requirement

Emphasizes the need to match setup to machine encoders.