Model NT-6926
Rechargeable, Dual Head
LED Work Light
with Telescoping Tripod
The NextLED Rechargeable, Dual Head LED Work Light with
Telescoping Tripod is designed to meet a wide variety of lighting
applications. Super bright, up to 5,000 lumens on high power,
1,500 lumens on medium power and 500 lumens on low power, it
offers both bright white and daylight modes of operation for all three
settings. It has two power options; rechargeable battery for shorter
duration use and corded for extended duration use. With its easy
and infinite adjustment options, it can place light exactly where you
need it. The tripod base fully extends to 75.5” and folds compactly
to just 35” for convenient transporting and storage and features
tough, lightweight aluminum construction. Includes two lithium ion
rechargeable batteries and charging cable.
CAUTION:
Read all instructions and warnings before operating!
SAVE THESE INSTRUCTIONS!
WARNING: To avoid serious injury or death from electrical shock or fire:
1. This fixture MUST ALWAYS BE USED IN ACCORDANCE WITH ALL
ELECTRICAL AND SAFETY CODES AND ORDINANCES, including
the most recent National Electric Code (NEC) and with the
Occupational Safety and Health Act (OSHA) Volume 1 on General
Industry Standards and interpretations.
2. ALWAYS make certain that the power source conforms to the rating
on the fixture.
3 DO NOT inspect or service the fixture while charging.
4. CAUTION: This fixture is for indoor use. Keep dry. Do not open,
drop, short-circuit, incinerate, expose to temperatures higher
than 140ºF, or charge/use if damaged.
5. People with pacemakers should consult their physician(s) before
use. Electromagnetic fileds in close proximity to heart pacemaker
could cause pacemaker interferance or pacemaker failure
6. This fixture is not explosive-proof, DO NOT use in potentially
dangerous locations, such as in flammable or explosive
atmospheres.
7. NEVER operate the light with the clear protective glass
broken or removed.
8. NEVER LOOK DIRECTLY INTO LIGHT SOURCE. LED’s are extremely
bright and can damage eyes with prolonged exposure.
9. KEEP AWAY from heating vents, radiators, or other sources of heat.
10. KEEP OUT OF REACH OF CHILDREN.
MAINTENANCE
Only qualified service personel must perform repairs. Opening or
visible attempts to open or repair work light will void any warranty
and/or cause damage to the product or personal injury.
CAUTION! Do not use solvents such as gasoline,
turpentine, etc. to clean the unit. Aerosols and other
chemical will fog the clear polycarbonate lens.
LITHIUM BATTERY SAFETY WARNINGS
LITHIUM BATTERIES STORE A LARGE AMOUNT OF ENERGY AND
WILL VENT FIRE OR EXPLODE IF MISTREATED:
1. Keep work light dry.
2. DO NOT DO ANY OF THE FOLLOWING TO BATTERY PACK:
a. Drop d. Puncture
b. Open e. Incinerate
c. Short-circuit f. Expose to temperatures
greater than 140ºF.
3. Charge work light only according to these instructions
BATTERY OPERATION
1. Press the lower power button to turn on the
LED light to the lowest illumination setting
of 500 lumens.
2. Press the lower power button again quickly,
to brighten the light to the medium setting
of 1,500 Lumens.
3. Press the lower power button a third time
quickly, for the full power of 5,000 Lumen
LED lights.
4. Press lower power button a final time to turn the light off.
CORDED OPERATION
1. Press the lower power button to turn on the LED light to
1,700 lumens.
2. Press lower power button a final time to turn the light off.
TO ALTERNATE BETWEEN BRIGHT WHITE LED
AND DAYLIGHT LED
1. Press the lower Power button to your
desired illumination level.
2. Press the upper lighting selection button
to alternate between the Bright White
LED light setting and the Daylight
LED setting.
TRIPOD SETUP
1. Unlatch the top release lever to loosen.
Slide the top portion to desired height and
lock into place.
2. Unlatch the bottom release lever to loosen.
Slide the bottom portion to desired height
and lock into place
Tips & Tricks: If the latch is too loose or
too tight, we have designed a standard
Philips screw allowing you to slightly tighten
or loosen the latch locking tension to your
desired setting.
3. To set up legs, simply pull each of the three
legs downward, until they automatically lock into place.
4. Unlatch the top release lever to loosen the top bar. Now, the
top tripod bar is fully rotatable for 360 degree LED positioning,
without needing to move the legs
To Next Page
Need help?
General
