Nice SMILO Series

Introduction
The SMILO series of radio control devices is
based on a system for sending a coded signal
from a transmitter to a receiver. If this signal is
recognised as valid, it activates the output
relays. The SMILO system uses the “rolling
code” transmission technique which makes the
radio control device extremely safe. This
method ensures that the recognition code is
different for each transmitter and that it
changes every time it is used.
Introduzione
Il radiocomando SMILO è un sistema che,
mediante un trasmettitore, invia al ricevitore un
“segnale” che, se riconosciuto come valido,
provoca l’attivazione dei relè d’uscita. SMILO
utilizza una tecnica di trasmissione denominata
a codice variabile (Rolling Code) che rende il
Vostro radiocomando estremamente sicuro.
Infatti mediante questa tecnica il codice di
riconoscimento è diverso per ogni trasmettitore
ed inoltre cambia ogni volta che viene utilizzato.
GB
I
remote controls
Introducción
El radiomando serie “SMILO” es un sistema
basado sobre el envío de una señal codificada
desde el transmisor al receptor. Si dicha señal
es reconocida como válida, provoca la
activación de los relés de salida. El sistema
SMILO utiliza una técnica de transmisión
denominada de código variable (Rolling Code),
que garantiza una extrema seguridad de los
radiomandos. Por medio de esta técnica, el
código de reconocimiento es distinto para cada
transmisor y cambia cada vez que es utilizado.
Introduction
La radiocommande série “SMILO” est un
système basé sur l’envoi d’un signal codé de
l’émetteur au récepteur. Si ce signal est
reconnu comme valable, il provoque l’activation
des relais en sortie. Le système SMILO utilise
une technique de transmission dite à code
variable (Rolling Code) qui rend la
radiocommande extrêmement sûre. Grâce à
cette technique, le code d’identification est
différent pour chaque émetteur et change à
chaque fois qu’il est utilisé.
Einleitung
Bei der Fernbedienung der Serie “SMILO”
handelt es sich um ein System, das auf der
Übertragung eines codierten Signals vom
Sender zum Empfänger beruht. Wird dieses
Signal als gültig anerkannt, so verursacht es die
Aktivierung der Ausgangsrelais. SMILO
verwendet eine Übertragungstechnik mit
variablem Code (Rolling Code), das die
Fernbedienung sehr sicher macht. Bei dieser
Technik ist der Erkennungscode für jeden
Sender anders und er ändert sich bei jeder
Verwendung.
Wstęp
Pilot radiowy z serii "SMILO"jest systemem
opartym na przesyłaniu sygnału kodowanego
z nadajnika do odbiornika. Gdy sygnał jest
pozytywnie rozpoznany przez odbiornik, to
powoduje uaktywnienie przekaźników
wyjścia. System "SMILO" stosuje technikę
przekazywania ze zmiennym kodem (Rolling
Code), który powoduje, że pilot jest
nadzwyczaj bezpieczny i pewny. Poprzez
zastosowanie tej techniki kod rozpoznawania
jest inny dla każdego nadajnika i zmienia się
przy każdorazowym użytkowaniu.
F E
D PL
smilo

Nice SMILO Series Specifications

General

Frequency	433.92 MHz
Coding	Rolling code
Operating Temperature	-20°C to +55°C
Number of Channels	2 or 4 channels
Battery	12V (23A)

Summary

Introduction to the SMILO System

SMILO System Overview

SMILO system for sending coded signals from transmitter to receiver, activating output relays.

Installation Guide

Transmitter Setup

SM2 and SM4 transmitters are ready to use. Check red LED for transmission confirmation.

Receiver Setup

SMX2 receiver is for universal use, provides circuit protection, can be fixed with adhesive or screws.

Receiver Power Input Selection

Use jumper to select power input: 24 V ac/dc (not inserted) or 12 V ac/dc (inserted).

Receiver Electrical Connections

Details wiring for power input, relay outputs (NO contacts), and aerial connection.

Receiver Output Contact Modification

Modify receiver output from normally open (NO) to normally closed (NC) by cutting track and soldering pads.

Aerial Installation and Requirements

Requires ABF or ABFKIT aerial for range. Proper installation and cable types are crucial.

Transmitter Programming Mode I

Single memorization phase per transmitter. Each button activates corresponding receiver output.

Transmitter Programming Mode II

Each transmitter button associated with a particular receiver output. More memory sections used.

Step-by-Step Mode I Memorization

Press receiver button for 3s, release when LED lights up, press transmitter button within 10s.

Step-by-Step Mode II Memorization

Press receiver button for output, check LED flashes, press transmitter button within 10s.

Remote Transmitter Memorization

Memorize a new transmitter using an already enabled and working remote control.

Deleting All Transmitters

Procedure to cancel all codes stored in the receiver memory by pressing and holding the receiver button.

Maintenance and Technical Specifications

Product Disposal Guidelines

Dispose of product according to local laws. Recycle materials where possible. Avoid polluting the environment.

Transmitter Specifications (SM2 SM4)

Details carrier frequency, coding, radiated power, buttons, power input, absorption, temp, dimensions.

Receiver Specifications (SMX2)

Details memory, input impedance, sensitivity, power input, absorption, relays, contacts, timing, temp, protection, dimensions.

EC Declaration of Conformity

Declaration Details

Contains declaration number, date, revision, producer name, address, product type, and model.

Compliance with Community Directives

Lists compliance with R&TTE, EMC, and Low Voltage directives.

Compliance with Harmonized Standards

Lists compliance with ETSI EN 300 683 and ETSI EN 300 330 standards.

European Country Notification

SMILO transmitters and receivers have been notified to major European countries.