What to do if 'Err' blinks on my Nikon F80?
If 'Err' blinks on your Nikon Film Camera, it indicates a malfunction. Try releasing the shutter again. If the warning persists or appears frequently, contact an authorized Nikon dealer or service center.
What to do if shutter speed indication blinks on Nikon F80?
The shutter speed indication blinks because a shutter speed faster than the sync speed is selected in S or M mode. To take a flash picture, release the shutter as it is. The shutter speed will automatically shift to 1/125 sec.
What to do if electronic analog exposure display blinks on Nikon F80?
The electronic analog exposure display blinks because the subject's brightness is beyond the camera’s exposure range. If the subject is too bright, use an ND filter. If the subject is too dark, use flash. Note that the display remains blinking when a Speedlight is used.
Why does HI appear on my Nikon Film Camera?
The 'HI' indication appears as an overexposure warning, meaning the subject is too bright. To resolve this: in P mode, use an ND filter; in S mode, select a faster shutter speed; in A mode, select a smaller aperture (larger f-number). If the warning persists in S or A mode, use an ND filter.
Why does Lo appear on my Nikon F80?
The 'Lo' indication appears as an underexposure warning, meaning the subject is too dark. To fix this: in P mode, use flash; in S mode, select a slower shutter speed; in A mode, select a larger aperture (smaller f-number). If the warning persists in S or A mode, use flash as well.
What to do if o–– and frame counter blink on Nikon Film Camera?
The 'o––' and frame counter blink because the camera back was opened during film rewind. To resolve this, immediately close the camera back and restart rewinding the film by pressing the two buttons.
What to do if 'End' blinks on my Nikon Film Camera?
The 'End' indication blinks because the end of the film roll has been reached (when ·1 is selected). To rewind the film, press the two film rewind buttons.
What does it mean when / blinks on my Nikon F80 Film Camera?
The '/' blinking indicates that autofocus is not possible. You should focus manually.
Why does 'buLb' blink on my Nikon F80?
The 'buLb' indication blinks because the shutter speed is set to 'buLb' in S mode. To resolve this, cancel the 'buLb' setting by selecting a shutter speed of 30 seconds or faster, or switch to M mode to perform a Long Time Exposure.
Why fiblinks for 3 sec. after flash on Nikon F80?
The fiblinks for 3 seconds after flash indicates that the flash fired at full output, potentially causing underexposure. To correct this, shoot again after verifying the focus distance, aperture, or flash shooting distance range.
Selects between Single Area AF and Dynamic AF modes for controlling focus points.
Provides illumination in dark conditions to aid autofocus operation.
Instructions for setting focus manually when autofocus is unreliable or unavailable.
Automatically captures multiple shots with different exposure settings for optimal results.
Captures extended exposures, useful for night scenes or stars, requires tripod.
Allows checking depth of field and shows the film plane position for accurate focusing.
Adjusts flash output level to intentionally alter subject brightness or background exposure.
General| Type | 35mm SLR Film Camera |
|---|---|
| Lens Mount | Nikon F mount |
| Autofocus | Yes |
| Metering Modes | 3D Matrix, Center-weighted, Spot |
| Flash Sync Speed | 1/125 sec |
| Power Source | 2 x CR123A lithium batteries |
| Focus Modes | Single, Continuous, Manual |
| Viewfinder | Fixed eye-level pentaprism |
| Exposure Modes | Program, Shutter-priority, Aperture-priority, Manual |
| Flash | Built-in pop-up flash |
| Film Advance | Automatic |
| Dimensions | 141.5 x 98.5 x 71 mm |
| Weight | 515 g (without batteries) |
| ISO Range | ISO 25 to 5000 (with DX coding) |
To Next Page
