S
Sandra HuffSep 6, 2025
How to check power cord connection on Nilfisk-ALTO Pressure Washer?
- JJamie ReedSep 6, 2025
To address power issues with your Nilfisk-ALTO Pressure Washer: * Check the power cord connection. * Check the fuse.
To Next PageTo Next PageHow to check power cord connection on Nilfisk-ALTO Pressure Washer?
To address power issues with your Nilfisk-ALTO Pressure Washer: * Check the power cord connection. * Check the fuse.
What to do if my Nilfisk-ALTO Pressure Washer shows a Fue error?
If your Nilfisk-ALTO Pressure Washer displays a Fue error, it indicates a fuel shortage. Simply fill the fuel tank. Cold water operation is possible.
What to do if my Nilfisk-ALTO NEPTUNE 5 Pressure Washer shows HOS error?
If your Nilfisk-ALTO Pressure Washer shows HOS error, contact Nilfisk-Alto Service.
What to do if my Nilfisk-ALTO NEPTUNE 5 Pressure Washer displays LHE error?
If your Nilfisk-ALTO Pressure Washer displays an LHE error, it could be due to a sooted flame sensor or an ignition or fuel system failure. Clean the flame sensor. Contact Nilfisk-Alto Service. Cold water operation is possible.
What to do if my Nilfisk-ALTO Pressure Washer displays LHL error?
If your Nilfisk-ALTO Pressure Washer displays an LHL error, it indicates a burner failure. Contact Nilfisk-Alto Service. Cold water operation is possible.
What to do if Nilfisk-ALTO NEPTUNE 5 motor overheated?
If the motor of your Nilfisk-ALTO Pressure Washer overheats: * Turn the main switch to the „OFF“ position and let the machine cool down. * Remove any extension cords being used. * Have the electrical connections checked for possible phase failure.
What to do if the flame sensor is sooted on my Nilfisk-ALTO Pressure Washer?
If the flame sensor of your Nilfisk-ALTO Pressure Washer is sooted due to ignition or fuel system failure, clean the flame sensor. Cold water operation is possible.
Why Nilfisk-ALTO NEPTUNE 5 has inadequate water supply?
If your Nilfisk-ALTO Pressure Washer has an inadequate water supply, it could be due to several reasons: * The water supply might be turned off. * The detergent tank might be empty; if so, fill it or set the detergent metering to „OFF“. * The pressure regulation on the safety control block or VarioPress-lance might be set to low water volume; if so, turn the twist grip on the safety control block or VarioPress-lance to a higher water/pressure volume. * The machine might be scaled. Ensure the required volume flow and pressure are within the specifications.
Why Nilfisk-ALTO NEPTUNE 5 Pressure Washer runs with pulsating pressure and makes knocking noise?
If your Nilfisk-ALTO Pressure Washer is running with pulsating pressure and making knocking noises, it is likely that the pump has drawn in air because the detergent tank is empty. To resolve this: * Close the detergent valve. * Remove the lance from the gun. * Operate the spray gun and let the machine run until the air in the pump is gone and the machine is running normally/calm again.
What to do if my Nilfisk-ALTO Pressure Washer is leaking or operating in short cycles?
If the Nilfisk-ALTO Pressure Washer switches off after three short-time operations, turn the main switch to the “OFF” position and then start it again, keeping the trigger squeezed for longer than 3 seconds to reset it. If the machine starts and stops briefly three times due to a leak in the hose or gun, it will switch off. You may need to repair the spray gun, replace the high-pressure hose, retighten screw fittings, fill the detergent tank or set detergent metering to “OFF”, clean the filter, or repair any leaks.
General| Brand | Nilfisk-ALTO |
|---|---|
| Model | NEPTUNE 5 |
| Category | Pressure Washer |
| Language | English |
