Nilfisk-ALTO NEPTUNE 5

Other manuals for Nilfisk-ALTO NEPTUNE 5

Instrukcja Obslugi21 pages

Questions and Answers

T
Theresa BairdNov 22, 2025
What to do if my Nilfisk-ALTO NEPTUNE 5 Pressure Washer is leaking (LEA)?
- J
  Jonathan HermanNov 22, 2025
  If your Nilfisk-ALTO Pressure Washer is leaking, it could be due to several reasons: * Leakage or inadmissible operating condition by short-time operation. * Spray gun leaking. * High pressure hose, coupling or line system leaking. * Detergent tank empty. * Water inlet filter dirty. * High-pressure pump drawing in air. Here are some suggested solutions: * After three times of short-time operation the machine switches off. To reset: Turn main switch to position “OFF“, then start again. Keep trigger squeezed for longer than 3 seconds. If a leak occurs in the hose and gun and causes the machine to start and stop briefly 3 times, then the machine will switch off. * Repair the spray gun. * Replace the high-pressure hose or retighten screw fittings. * Fill the detergent ta...
T
taylorcassandraAug 25, 2025
What to do if my Nilfisk-ALTO Pressure Washer shows a Fue error?
- J
  Johnny BarnesAug 26, 2025
  If your Nilfisk-ALTO Pressure Washer displays a Fue error, it indicates a fuel shortage. Simply fill the fuel tank. Cold water operation is possible.
A
allenlewisAug 26, 2025
What to do if my Nilfisk-ALTO NEPTUNE 5 Pressure Washer shows HOS error?
- R
  Ryan JacobsAug 27, 2025
  If your Nilfisk-ALTO Pressure Washer shows HOS error, contact Nilfisk-Alto Service.
D
Donald FisherAug 27, 2025
What to do if my Nilfisk-ALTO NEPTUNE 5 Pressure Washer displays LHE error?
- K
  klawrenceAug 27, 2025
  If your Nilfisk-ALTO Pressure Washer displays an LHE error, it could be due to a sooted flame sensor or an ignition or fuel system failure. Clean the flame sensor. Contact Nilfisk-Alto Service. Cold water operation is possible.
K
Katie TerryAug 28, 2025
What to do if my Nilfisk-ALTO Pressure Washer displays LHL error?
- K
  Kevin HicksAug 28, 2025
  If your Nilfisk-ALTO Pressure Washer displays an LHL error, it indicates a burner failure. Contact Nilfisk-Alto Service. Cold water operation is possible.
S
Sandra BrockSep 15, 2025
What to do if Nilfisk-ALTO NEPTUNE 5 motor overheated?
- E
  Edward KnoxSep 15, 2025
  If the motor of your Nilfisk-ALTO Pressure Washer overheats: * Turn the main switch to the „OFF“ position and let the machine cool down. * Remove any extension cords being used. * Have the electrical connections checked for possible phase failure.
M
Martha MartinezSep 12, 2025
What to do if the flame sensor is sooted on my Nilfisk-ALTO Pressure Washer?
- V
  Vincent JohnstonSep 12, 2025
  If the flame sensor of your Nilfisk-ALTO Pressure Washer is sooted due to ignition or fuel system failure, clean the flame sensor. Cold water operation is possible.
J
Joseph MitchellSep 14, 2025
Why Nilfisk-ALTO NEPTUNE 5 has inadequate water supply?
- L
  Lisa HuffSep 14, 2025
  If your Nilfisk-ALTO Pressure Washer has an inadequate water supply, it could be due to several reasons: * The water supply might be turned off. * The detergent tank might be empty; if so, fill it or set the detergent metering to „OFF“. * The pressure regulation on the safety control block or VarioPress-lance might be set to low water volume; if so, turn the twist grip on the safety control block or VarioPress-lance to a higher water/pressure volume. * The machine might be scaled. Ensure the required volume flow and pressure are within the specifications.
M
Melissa MelendezSep 5, 2025
Why Nilfisk-ALTO NEPTUNE 5 Pressure Washer runs with pulsating pressure and makes knocking noise?
- Z
  Zachary GonzalezSep 5, 2025
  If your Nilfisk-ALTO Pressure Washer is running with pulsating pressure and making knocking noises, it is likely that the pump has drawn in air because the detergent tank is empty. To resolve this: * Close the detergent valve. * Remove the lance from the gun. * Operate the spray gun and let the machine run until the air in the pump is gone and the machine is running normally/calm again.
D
David BarnesSep 3, 2025
What to do if my Nilfisk-ALTO Pressure Washer is leaking or operating in short cycles?
- M
  Mark FrankSep 3, 2025
  If the Nilfisk-ALTO Pressure Washer switches off after three short-time operations, turn the main switch to the “OFF” position and then start it again, keeping the trigger squeezed for longer than 3 seconds to reset it. If the machine starts and stops briefly three times due to a leak in the hose or gun, it will switch off. You may need to repair the spray gun, replace the high-pressure hose, retighten screw fittings, fill the detergent tank or set detergent metering to “OFF”, clean the filter, or repair any leaks.