How to fix low pressure on my Nilfisk-ALTO NEPTUNE DE?
If the pressure is too low on your Nilfisk-ALTO Pressure Washer, the high-pressure nozzle may be worn out, or the pressure regulation might be set to a low water volume. Try replacing the nozzle or turn the twist grip on the spray lance to a higher water volume.
What to do if green and red LEDs flash simultaneously on my Nilfisk-ALTO NEPTUNE DE?
If the green and red LEDs flash simultaneously on your Nilfisk-ALTO Pressure Washer, it indicates a leakage or an inadmissible operating condition due to short-time operation. This can be caused by a leaking spray handle, high-pressure hose, coupling, line system, dirty water inlet filter, or the high-pressure pump drawing in air. Check the spray handle, replace the high-pressure hose, retighten screw fittings, and clean the filter. After three times of short-time operation, the heating switches off. To reset, turn the main switch to the 'OFF' position, then start again. Keep the spray gun pressed for longer than 3 seconds. If a leak occurs causing the machine to start and stop briefly 3 times, then the heating will switch off. Cold water operation is possible.
Why my Nilfisk-ALTO NEPTUNE DE Pressure Washer is not turning ON?
If your Nilfisk-ALTO Pressure Washer is not turning on, the engine may not have started, the engine RPM may be too low, or the generator may be defective. Start the engine. For NEPTUNE 5-51DE models, adjust the RPM on the speed control to max. Cold water operation is possible.
What does it mean when the yellow LED is ON on my Nilfisk-ALTO NEPTUNE DE?
If the yellow LED is ON, it indicates a fuel shortage. Top up with fuel. Cold water operation is possible.
What does it mean when the red LED is ON on my Nilfisk-ALTO Pressure Washer?
The red LED being ON indicates a few potential issues with your Nilfisk-ALTO Pressure Washer. It could mean the service interval has expired, the pump oil or engine oil is low, the charging rate is too low, or the pump has overheated. In the case of low pump or engine oil, top up with the appropriate oil. If the pump overheated, let it cool down, and avoid long bypass times. If the charging rate is too low because the engine has not started, try to start it.
What does it mean when the green LED is flashing on my Nilfisk-ALTO NEPTUNE DE Pressure Washer?
If the green LED is flashing on your Nilfisk-ALTO Pressure Washer, it could indicate a flow sensor failure, a closed water tap or water shortage, or that the machine is scaled. Ensure the water tap is open and there is an adequate water supply. Required volume flow and pressure see section 9.4 Technical Specifications. Cold water operation is possible.
What to do if the pump overheated on my Nilfisk-ALTO Pressure Washer?
If the pump overheated on your Nilfisk-ALTO Pressure Washer, let the pump cool down. Avoid long by-pass time (NEPTUNE 5-46/ 5-54 PE, see section 4.2).
What to do if the charging rate is too low on my Nilfisk-ALTO Pressure Washer?
If the charging rate is too low on your Nilfisk-ALTO Pressure Washer, it could be because the engine has not started or the generator is defective. Try starting the engine.
How to fix low pump or engine oil on my Nilfisk-ALTO NEPTUNE DE Pressure Washer?
If the pump oil or engine oil is low, top up with pump oil and engine oil.
General| Brand | Nilfisk-ALTO |
|---|---|
| Model | NEPTUNE DE |
| Category | Pressure Washer |
| Language | English |
Explains safety, information, and operational symbols used in the manual.
Covers user safety, warnings, transport, and pre-operation checks for safe use.
Guidelines for maintenance and repair, emphasizing safety and authorized service.
Information on safety testing, regulatory compliance, and unloader valve function.
Details the intended professional applications and uses of the high-pressure cleaner.
Identifies and describes the various operating elements and controls of the machine.
Instructions for transporting, assembling, and setting the brake on the machine.
Steps for filling the fuel tank and connecting the water supply and high-pressure hose.
Steps for connecting the spray lance to the spray gun and other accessories.
Explains indicator lights, control panel functions, and switching on procedures.
How to adjust pressure and use cleaning agents effectively.
Various techniques like soaking, detergent use, temperature, and mechanical effects for efficient cleaning.
Specific cleaning tasks for agriculture, vehicles, and buildings/equipment.
Step-by-step procedure for safely shutting down and depressurizing the cleaner.
Instructions for storing the machine, including protection against frost damage.
Overview of recommended maintenance tasks and their frequency (weekly, operating hours, as required).
Step-by-step instructions for performing key maintenance tasks like filter cleaning and oil changes.
Explains indicator lights and their causes/remedies for diagnosing operational issues.
Lists common faults not related to display indicators and their corresponding solutions.
Information on recycling, warranty conditions, and CE declaration of conformity.
Lists detailed technical specifications for various models, including pressure, flow, dimensions, and weight.
To Next Page
