NOCRY NPS-100 DINS - User Manual

Questions and Answers

M
Michelle GallagherAug 2, 2025
Why is no coating material coming out of my NOCRY NPS-100 DINS Paint Sprayer nozzle?
- K
  Kenneth BurchAug 2, 2025
  If no coating material emerges from the nozzle of your NOCRY Paint Sprayer, several factors could be at play. The nozzle might be clogged, so try cleaning it with the included pin. Alternatively, the material volume could be set too low, so increase it. Check if the paint container seal is damaged and replace it if necessary. Ensure there's enough pressure build-up by tightening the container. Also, verify that the container isn't empty and refill it if needed. Lastly, make sure the feed tube is properly inserted and not clogged; reinsert or clean it with the included brush, ensuring the air vent is also clear.
J
Jasmine TaylorAug 6, 2025
Why does the spray jet pulsate on my NOCRY NPS-100 DINS?
- M
  Morgan CollinsAug 6, 2025
  If the spray jet of your NOCRY Paint Sprayer pulsates, it could be due to a few reasons. The coating material in the container might be running low, so refill it. The air filter could be soiled, so clean or change it. Also, the feed tube might have come loose, so reinsert it, or it could be clogged, so clean it with the included brush.
E
erinsweeneyAug 10, 2025
How to fix atomization that is too coarse with NOCRY NPS-100 DINS Paint Sprayer?
- L
  Leah NguyenAug 10, 2025
  If the atomization is too coarse with your NOCRY Paint Sprayer, it could be due to several reasons. The material volume might be too large, so reduce it. The nozzle tip might be contaminated, so clean it with the included pin. The viscosity of the coating material might be too high, so dilute it further. There might be too little pressure build up in the container, so tighten it. The air pressure might be too low, so increase the air volume with the air volume control.
J
Julie WilliamsAug 15, 2025
What to do if coating material drips from the nozzle of my NOCRY Paint Sprayer?
- C
  Courtney MartinAug 15, 2025
  If coating material drips from the nozzle of your NOCRY Paint Sprayer, it may be because the air cap, nozzle, or needle are soiled. Clean them with the included pin. Another cause could be that the spray attachment is incorrectly assembled; reassemble it according to the instructions. The spray nozzle cap may also be loose, so tighten it. If the nozzle tip hole is worn out, you'll need to replace the spray nozzle tip.
G
gcolemanAug 19, 2025
How to reduce excessive paint mist (overspray) from NOCRY NPS-100 DINS?
- K
  Karen PaulAug 19, 2025
  If you're experiencing excessive paint mist (overspray) with your NOCRY Paint Sprayer, it could be due to several factors. The distance to the object might be too large, so reduce it. You might be applying too much coating material, so reduce the material volume. The air pressure might be too high, so reduce the air volume. The coating substance might be over-diluted, so reduce the degree of dilution. Incorrect spraying technique can also cause this, so refer to “How to get the best results” on page 22.
S
Steven MurrayAug 23, 2025
Why does material run down the object when using NOCRY NPS-100 DINS Paint Sprayer?
- D
  Doris CollinsAug 25, 2025
  If material runs down the object being painted with your NOCRY Paint Sprayer, it's likely that too much coating material has been applied, so reduce the material volume. Alternatively, the distance might be too small, so increase the distance.
M
morganlindaAug 27, 2025
Why is there paint in the ventilating hole of my NOCRY NPS-100 DINS?
- R
  rtorresAug 27, 2025
  If you find paint in the ventilating hole of your NOCRY Paint Sprayer, it could be because the seal is dirty; clean the seal. Alternatively, the seal may be defective, so replace it.