2 Copyright © 2015 Nortek Security & Control
NOTE: To learn how to program a sensor into the Control Panel, see the Control
Panel's InstallaƟ on & Programming Guide.
Figure 8. Arrow label points upward
NOTE: Avoid moun ng the sensor in areas where it will be exposed to moisture or
where the sensor will be exposed to temperatures outside its opera ng range of 0
to 120° F (0 to 49° C). Avoid moun ng the sensor in areas with a large quan ty of
metal or electrical wiring.
Replacing Battery
Figure 9. Replacing the Ba ery
1. To remove the Sensor/Cover from the base, press a fl athead screwdriver into
the slot on the sides of the sensor, and turn the screwdriver 90°.
Figure 10. Removing the ba ery
2. Place a small fl athead screwdriver in the slot between the metal clip and
the ba ery, then twist the screwdriver slightly while holding back one of the
black plas c edges holding the ba ery. Dispose of ba ery.
IMPORTANT: Always dispose and/or recycle used ba eries in accordance with
the hazardous waste recovery and recycling regula ons for your loca on. Your
city, state, or country may also require you to comply with addi onal handling,
recycling, and disposal requirements.
3. Insert the replacement ba ery with the plus (CR 2032) (+) sign facing up.
4. Verify programming and RF communica on with the panel.
5. Replace the Sensor/Cover onto the Sensor Base being sure that the tamper
bu on is aligned with the tamper tab as shown in Figure 5.
SPECIFICATIONS
Typical ba ery life 5 to 8 years
Opera ng Temperature 2° to 120°F (0° to 49° C)
Opera ng Rel. Humidity 5 to 85%, non-condensing
Opera ng Frequency 345MHz
Tilt Switch Angle 45 degrees
REGULATORY INFORMATION
This equipment has been tested and found to comply with the limits for Class B
Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protec on against harmful interference in a residen al
installa on. This equipment generates and can radiate radio frequency energy
and, if not installed and used in accordance with the instruc ons, may cause
harmful interference to radio communica ons. However, there is no guarantee
that interference will not occur in a par cular installa on. If this equipment
does cause harmful interference to radio or television recep on, which can be
determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures.
• Reorient or relocate the receiving antenna
• Increase the separa on between the equipment and receiver
• Connect the equipment into an outlet on a circuit diff erent from that to
which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifi ca ons not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux
appareils radio exempts de licence. Ľexploita on est autorisée aux deux condi ons
suivantes: (1) ľappareil ne doit pas produire de brouillage, et (2) ľu lisateur de
ľappareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est suscep ble ďen comprome re le fonc onnement.
FCC COMPLIANCE STATEMENT
This device complies with FCC Rules and Regula ons as Part 15 devices as well as
Industry Canada license exempt RSS Rules and Regula ons. Opera on is subject to
the following two (2) condi ons: This device may not cause harmful interference.
This device must accept any interference received, including interference that may
cause undesired opera on.
LIMITED WARRANTY
This Nortek Security & Control LLC product is warranted against defects in material
and workmanship for two (2) years. This warranty extends only to wholesale
customers who buy direct from Nortek Security & Control LLC or through Nortek
Security & Control normal distribu on channels. Nortek Security & Control does
not warrant this product to consumers. Consumers should inquire from their
selling dealer as to the nature of the dealer’s warranty, if any.
There are no obliga ons or liabili es on the part of Nortek Security & Control for
consequen al damages arising out of or in connec on with use or performance of
this product or other indirect damages with respect to loss of property, revenue,
or profi t, or cost of removal, installa on, or reinstalla on. All implied warran es
for func onality, are valid only un l the warranty expires. This Nortek Security
&Control Warranty is in lieu of all other warran es expressed or implied.
Nortek Security & Control LLC
2GIG
1950 Camino Vida Roble, Suite 150
Carlsbad, CA 92008-6517 USA
For technical support in the USA and Canada:
855-2GIG-TECH (855-244-4832)
Email: 2gigtechsupport@nortek.com
Visit www.nortekcontrol.com for technical support hours of opera on
For technical support outside of the USA and Canada:
Contact your regional distributor
Visit dealer.2gig.com for a list of distributors in your region
TURN SCREWDRIVER
BLADE 90˚ TO OPEN
SENSOR
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,2GIG-TILT1-345 en - P/N: 10006166A - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 8.500” X 11.000” - TOL. +/- 0.020”- SCALE: 1-1- PAGE 2 OF 2 - FOLDING: FOLD 4X TO FINAL SIZE: 2.125" X 2.750"- FINISH WITH LOGO SHOWING
10006166 A
To Previous Page
Loading...
