Novoferm HAD MS - Error Diagnosis; E05 Door neither opens nor closes; E06 Door reverses; does not close; E07 Door reverses; does not close

ErrorDiagnosis
GB
Subject to changes
Error State Diagnosis/Remedy
E05 Door neither opens nor closes
E06 Door reverses / does not close Check menu setting [35].
E07 Door reverses / does not close .
E08 Door neither opens nor closes
E09 Door neither opens nor closes
E10
, exchange control unit.
No response , exchange control unit.
No response , exchange control unit.
No response , exchange control unit.
Safety edges defective,
Door neither opens nor closes
.
command given
F11 Valve 1 short circuit Valve 1, check feeding line.
F14 Valve 1 interruption Valve 1, check feeding line.
F17 No response dock leveller Fault in the hydraulic motor.
control for closing
Door responds only to dead man’s Photocell
control for closing
Door responds only to dead man’s
control for closing
F31 No response
.
F32 Door neither opens nor closes
F33 Door stopped while opening
Door neither opens nor closes
Door neither opens nor closes
F01
F2 No response
F3
F4
F5
F06 No response
F07
F09
F10 Door stops shortly after START
F19 Door responds only to dead man’s
F20
F21 Operation briefly interrupted
F22 Hydraulic motor cuts off
F23
F24
F25 No response
F26 No response
F28
F29
F30
The slack cable switch has tripped (see Fig. 8c).
Closing edge has been triggered.
Photocell has been triggered. Check menu setting [36]
External safety device (emergency-STOP, slack cable, wicket door, motor's thermal
switch) has been activated. Check (J4).
No end-of-travel positions learned. Programme the end-of-travel positions [30] [31].
Menu 36 set at 3 or 4 Allow door to open and close fully in order for the position of the photocell to be detected.
Error occurred during self-testing
Error occurred during self-testing
Error occurred during self-testing
Error occurred during self-testing
Check voltage (J3.3 - J3.1 >12V).
The 24V power supply has broken down. Check the connections.
Malfunction in the control unit electronics. Replace control unit
.
Closing edge self-testing has failed. Check safety edge.
self-testing has failed. Check photocell.
Door operator's excess travel stop activated, allow operator to cool down for approx. 20 min.
Motor pump's excess travel stop activated, operating error or defective button.
No response to START command Door's end-of-travel positions defective. Check end-of-travel positions and if necessary re-
adjust.
No response to START command No connection to DES. Check motor connecting lead and DES.
Internal testing of membrane keypad defective. Replace membrane keypad.
Internal testing of external buttons / switches has failed.
F27 Door end positions not obtained Adjust setting in menu 33/34.
Motor blocks Check door mechanical system / check motor connection cable.
No response to START command Fault in the voltage supply. Check mains connection.
Motor rotates in the wrong direction Mains phases have been exchanged; correct or reset.
Returns from impulse to dead man's control.
Check safety edges and photocell.
Button pressed when mains was switched on. Press mains isolator again.
Inspect safety wheel chock
Spring breakage detection has been activated. Check springs and if necessary replace and
programme the end-of-travel positions again.
Opening force limit activated. Thereafter, the door can only be closed via the dead man's
control. Eliminate sluggishness or blocking of door. Check springs. Eliminate the reason
for the excessive force being applied, so that the door can be opened and closed again.
F34 The ON period has been exceeded. Wait and let the motor cool down.
F35 The speed monitoring has tripped. Exchange DU drive.
F40 Expansion control The 24-V power supply has broken down. Check the connections at the expansion control.
F41 Expansion control Fault during the self-test. Replace the expansion control.
F43 Expansion control No connection.
L Access to the menu has been blocked Contact authorized dealer.
by the authorized dealer. Menu bock can only be lifted using service tool.
Lo Control unit has been blocked. Contact authorized dealer. Menu bock can only be lifted using service tool.
U Access block of the menu has been lifted
by the authorized dealer.
No movement of door / dock leveller Wrong mains voltage, check rotary field, change rotation.
Hydraulic motor cuts off The electricity control of the motor pump has tripped. Check menu setting [10].