Why NSS Scrubber machine will not turn on?
Your NSS Scrubber might not be turning on due to several reasons: - The battery pack may not be properly connected, in which case you should connect the battery pack. - The battery charger might be plugged in; unplug it. - The batteries could be discharged; charge them. - The circuit breaker may have tripped; reset it.
What to do if NSS Scrubber does not pick up water?
If your NSS Scrubber isn't picking up water, here's what you can check: - The recovery tank might be full, so drain it. - The float ball could be stuck; clean the float screen and ball. - The squeegee hose or standpipe may be plugged; clear them. - Ensure the squeegee hose is properly connected. - The squeegee blades might be worn; flip or replace them. - The squeegee blades could be loose; adjust the latch on the band clamp.
Why is the run time less than when new for my NSS Scrubber?
If your NSS Scrubber's run time is shorter than when it was new, consider the following: - Batteries might be damaged due to low electrolyte; fill each cell with distilled water, charge, and check for improvement. - Battery terminals could be dirty; clean them. - Batteries may not be fully charged; allow the charger to finish charging before unplugging. - The batteries might be worn out; replace them.
How to fix no water flow in NSS Scrubber?
If there's no water flow in your NSS Scrubber, check these: - The clean water filter might be clogged; clean the filter/screen. - The water valve could be closed; turn on the valve.
What causes uneven cleaning with NSS Scrubber?
Uneven cleaning with your NSS Scrubber may be due to: - Worn out pad/brush; replace pads/brushes.
Specific chemical warning related to California Proposition 65.
Reference to the battery safety information label on the machine.
Caution against using flammable liquids for cleaning.
Description of the key switch function for machine operation.
Explanation of the battery charge level indicator symbols.
Identification of the brush/vacuum switch and fuse.
Illustration of circuit breakers for the Wrangler 2012 AB.
Illustration of circuit breakers for the Wrangler 2012 DB.
Indication of head pressure measurement values.
Location of the clean water valve.
Location of the clean water strainer.
Guidance on the correct direction for pad driver installation.
Identification of the pad driver release lever.
Allows operator to view battery charger operation status.
Connection point for the battery charger power cord.
Rear access point for filling the solution tank.
Adjusts pressure applied by the brush/pad motor.
Storage feature for the battery charger power cord.
Operates the brush/pad motor raising and lowering mechanism.
Connects the vacuum head to the recovery tank.
Used to secure the squeegee in place.
Controls the movement of the squeegee to and from the floor.
Component that collects dirty solution from the floor.
Filters debris from the solution before it reaches the brush.
Controls the flow rate of the cleaning solution.
Prevents solution splash-out from under the skirt.
Protects users from moving parts and contains solution.
Facilitates brush/pad removal.
Hose for draining the battery compartment.
Visual indicator for the solution tank fluid level.
Holds the cleaning solution for the machine.
Hose used to empty the recovery tank.
Protective cap for the recovery tank drain hose.
Collects dirty solution and debris from the floor.
Covers the recovery tank opening.
Turns the vacuum motor on and off.
Activates the brush/pad motor and solution dispensing.
Protective fuse for the battery charger circuit.
Prevents water from entering the vacuum motor.
Collects large debris to prevent hose clogs.
Access point for filling the solution tank.
Location of the machine's batteries.
Connects the battery pack to the machine.
Drives the vacuum fan for water pickup.
Facilitates lifting and moving the recovery tank.
Controls machine direction and speed.
Indicates battery condition and charge level.
Enables or disables machine operation.
Protects the brush motor circuit.
Protects drive system and controller.
Protects the vacuum motor circuit.
Protects the brush motor circuit.
Protects the vacuum motor circuit.
Allows operator to control machine direction.
Activates brush/pad motor and solution valve.
Indicates battery status and motor runtime.
Enables or disables machine operation.
Key safety precautions for machine use and operation.
Information on protective devices integrated into the machine.
Explanation of hazard and caution symbols used in the manual.
Defines the appropriate commercial applications for the machine.
Critical safety precautions for operating the machine.
Essential safety guidelines for handling and charging batteries.
Procedure for inspecting the machine for damage after unpacking.
Steps to prepare the machine for its initial operation.
Location and basic functions of the machine's control panel.
Details on the solution tank's capacity and features.
Details on the recovery tank's capacity and function.
Operation and adjustment of the solution flow control.
Maintenance and cleaning of the solution filter.
Information on the brush/pad motor and its service.
Mechanism for adjusting brush/pad pressure.
Components and maintenance of the squeegee.
Details on the vacuum motor and its service.
Location and access to the battery compartment.
Location and operation of the onboard battery charger.
Location of DIP switches for charger configuration.
Configuration options for charging curves using DIP switches.
Steps for correctly installing the squeegee.
Procedure for installing pads or brushes.
Instructions for filling the clean water tank.
Routine cleaning of the clean water filter.
Daily cleaning and inspection of the squeegee.
Inspection and replacement of pads and brushes.
Procedure for draining the battery compartment.
Guidelines for maintaining and charging the machine's batteries.
Method for charging batteries during short breaks.
Tasks required for monthly machine upkeep.
Proper methods for cleaning the machine's exterior.
Required maintenance tasks at specific intervals.
Specifications for standard and AGM batteries.
Features and ratings of the battery charger.
Recommended storage conditions for the machine.
Guidelines for proper disposal of the machine.
To Next Page
General
