Numax SBR50 - Page 3

MODEL: SBR50
NUMA.
TOOL USE AND CARE
9 Know this tool. Read manual carefully, learn
its applications and limitations, as well as the
specific potential hazards related to this tool.
© Use only fasteners that are recommended
for your models. Do not use the wrong
fasteners or load the fasteners incorrectly.
© Check for misalignment or binding of
moving parts, breakage of parts, and any
other condition that may affect the tool's
operation. If damaged, have the tool serviced
before using. Many accidents are caused by
poorly maintained tools.
ө Maintain tools with care. Keep tool clean. A
properly maintained tool, reduces the risk of
binding and is easier to control.
© Store tools out of the reach of children and
other untrained people. Tools are dangerous
in the hands of untrained users.
9 Check operation of the tool before use. Do
not use the tool if the workpiece contact
mechanism is not working correctly as
accidental driving of a fastener may occur.
@ Do not use tool if trigger does not actuate
properly. Any tool that cannot be controlled
with the trigger is dangerous and must be
repaired.
© Do not force tool. Use the correct tool for your
application. The correct tool will do the job better
and safer at the rate for which itis designed.
© Use clamps or another practical way to
secure and support the workpiece to a
stable platform. Holding a tool by hand or
against the body is unstable and may lead to
loss of control.
© Keep the tool and its handle dry, clean and
free from oil and grease. Always use a clean
cloth when cleaning. Never use brake fluids,
gasoline, petroleum-based products, or any
strong solvents to clean your tool.
© Do not use the tool as a hammer.
© Never use this tool in a manner that could
cause a fastener to be directed toward
anything other than the workpiece.
© Always carry the tool by the handle. Never
carry the tool by the air hose.
© Do not use the tool if it leaks air or does not
function properly.
ө Do not operate the tool if it does not contain
alegible warning label.
TOOL SERVICE
© Use only accessories that are identified by
the manufacturer for the specific tool model.
ө Use of unauthorized parts or failure to
follow maintenance instructions may
create a risk of injury.
ө Use only the lubricants supplied with the
tool or specified by the manufacturer.
9 Tool service must be performed only by
qualified repair personnel.
OPERATION
© Do not drive fasteners near edge of material.
The workpiece may split causing the fastener or
ricochet, injuring you or people around.
© Do not carry the tool from place to place
holding the trigger. Accidental discharge
could result. Choice of triggering method is
important. Check manual for triggering options.
ө During normal use the tool will recoil
immediately after driving a fastener. This is
а normal function of the tool. Do not attempt to
prevent the recoil by holding the tool against the
work. Restriction to the recoil can result in а
second fastener being driven from the tool. Grip
the handle firmly and let the tool do the work.
Failure to heed this waming can result in
serious personal injury.
ө Do not drive fasteners on top of other
fasteners or with the tool at an overly steep
angle as this may cause deflection of
fasteners which could cause injury.
© Do not actuate the tool unless you intend to
гіме a fastener into the workpiece.
© Always handle the tool with care:
Respect the tool as a working implement.
% Never engage in horseplay.
% Never pull the trigger unless nose is directed
toward the work.
Keep others a safe distance from the tool
while tool is in operation as accidental
actuation may occur, possibly causing injury.
AIR SUPPLY AND CONNECTIONS
© The connector on the tool must not hold
pressure when air supply is disconnected. If
an incorrect fitting is used, the tool can remain
charged with air after disconnecting and thus
will be able to drive а fastener even after the air
line is disconnected, possibly causing injury.
02 HTTP:/WWW.NUMAXTOOLS.COM 1-888-669-5672
MODEL: SBR50
МОЛЛУ
@ Do not use oxygen, combustible gases or
bottled gasses as a power source for this
tool. Explosion may occur, causing injury or
death.
@ Do not connect with an air compressor
which can potentially exceed 200 Psi.
As tool may burst, possibly causing injury.
ө Always disconnect air resource:
Before making adjustments.
When servicing the tool.
When clean a jam.
When tool is not in use.
When moving to a different work area, ав
accidental actuation may occur, causing injury.
LOADING TOOL
© Do not load the tool with fasteners when
any one of the operating controls is
activated.
© Never place a hand or any part of body іп
fastener discharge area of tool.
© Never point tool at anyone.
© Do not pull the trigger or depress the
workpiece contact as accidental actuation
may occur, possibly causing
А WARNING:
The warnings and precautions discussed
above cannot cover all possible
conditions and situations that may occur.
It must be understood by the user that
common sense and caution are factors
which cannot be built into this product,
but must be supplied by the user.
UNPACKING
@ This tool has been shipped completely
assembled.
ө Make sure that all items listed in the packing
list are included.
@ Carefully remove the tool and any
accessories from the box.
© Inspect the tool carefully to make sure по
breakage or damage occurred during
shippin
© Do not discard the packing material until you
have carefully inspected and satisfactorily
operated the tool.
© if any parts are damaged or missing, please
call 1-888-669-5672.
PACKING LIST
Brad nailer
Air connector
Adjustment tools
Lubricating oil
Instruction manual
Anti-dust cap
А WARNING:
If any parts are missing do not operate
this tool until the missing parts are
replaced. Failure to do so could result in
possible serious personal injury.
А WARNING:
Do not attempt to modify this tool or
create accessories not recommended for
use with this tool. Any such alteration or
modification is misuse and could result
in hazardous condition leading to
possible serious personal injury.
FEATURES
SPECIFICATIONS
Operation pressure: | 60-100psi
Nails capacity: 100pcs
Tool weight: 2.86 lbs
Air inlet: 1/4"NPT
Fasteners: 18 Gauge
0.116(2тт)
10mm
15mm 5/8"
20mm з
2бтт | 1" Re
32MM | 1-4/4" 38
Жат 1/2 T
45mm 1-34 0.041"
50тт 2 (1.05mm)
Compatible with Porter Cable, Paslode, Senco,
& All Generic 18 Gauge Straight Nails.
HTTP:/WWW.NUMAXTOOLS.COM 1-888-669-5672 03