NUTOOL NCD144 - Guard Against Electric Shock; Power Cords

13
GB
function.
Check correct alignment of moving parts, making sure they do
notbind.Checkforanydamagedcomponentsandmakesure
thatthepowertoolhasbeencorrectlyassembled.
Check for any condition that may affect operation of the power
tool.
Unless otherwise indicated in this instructions handbook, a
guard or any other part of the power tool that has been damaged
mustberepairedorreplacedbyanauthorizedservicecenter.
Anyswitchthatdoesnotworkcorrectlymustbereplacedbyan
authorizedservicecenter.
Do not use the power tool if the ON/OFF switch does not turn
thepowertoolONandOFF.
Dustgeneratedwhenmachiningmaterialsisahealthhazard.
Alwayswearasuitabledustmask.
When working, always wear personal protective equipment:
safety goggles, gloves, mask, ear protectors, non-slip safety
shoes.
Never wear loose clothes or jewelry that may be trapped in
movingparts;longhairmustbetiedback.
Alwaysworkonastablebase.
Alwaysfastentheworkpiecesecurelywithaclamp.
Keeptheworkareacleanandtidy.
Alwaysusethepowertoolwithbothhands.
Never open or modify the power tool or its accessories in
anyway.
Do not expose the power tool to rain, or use in damp or wet
locations.Keeptheworkareawelllit.
Do not use power tools in areas where there is a risk of explosion
or fire from combustible materials, flammable liquids, paint,
varnish,petroletc.flammablegasesanddustofanexplosive
nature.

Childrenandpetsshouldbekeptoutoftheworkarea.
Allpowertoolsshouldbekeptoutofthereachofchildrenand,
preferably, stored or locked in a secure cabinet or dry room
whennotinuse.

Selecttherighttoolforthejob.Donotuseatoolforajobfor
whichitwasnotdesigned.Donotforceasmalltooltodothe
job of a heavy-duty tool. Do not use tools for purposes not
intended.

The power tool will do a better and safer job and give you much
betterserviceifitisusedattherateforwhichitwasdesigned.

Keep cutting tools sharp and clean for better and safer
performance.
Followtheinstructionsforlubricatingandchangingaccessories.
Keephandlesdry,cleanandfreefromoilandgrease.
Ensure that ventilation slots are kept clean and free from dust
atalltimes.Blockedventilationslotscancauseoverheatingand
damagetothemotor.
If this machine is to be used when working at a certain height,
scaffoldingfittedwithrailingandkick-plateoratowerplatform
mustbeusedinordertoguaranteesuitablestability.

Avoid body contact with earthed or grounded surfaces (e.g.
pipes,radiators,dish-washersandrefrigerators).

Never yank or pull the power cord to disconnect it from the
mainssupplysocket.
Nevercarrythepowertoolbyitspowercord.Keepthepower
cordawayfromheat,oil,solventsandsharpedges.
Check the tool power cord periodically and if damaged have it
replacedbyanauthorizedservicecenter.
Inspectextensioncordsperiodicallyandreplaceifdamaged.
DONOTuse 2-coreextensioncords orreelsonpowertools
withanearthpath.Alwaysusea3-coreextensioncordorreel
withtheearthcoreconnectedtoearth.
Alwaysunwindanyextensioncordsfully.
Forextensioncordsupto15metres,useawirecrosssection
of1.5mm
2
.
Forextensioncordsover15metres,useawirecrosssection
of2.5mm
2
.
Protect your extension cord from sharp objects, excessive heat
anddamporwetlocations.
 
      


