Nutradip GrowBoss User Manual

Troubleshooting Guide
Problem - No Display
Follow the steps below until a solution is reached:
1. Check that the Growboss is connected to the 5dcv/0.5 amp
power supply
2. Check that the Power supply is connected to the wall outlet
3. Verify that the outlet has power by connecting another
device such as a lamp or fan
4. Unplug all cords and probes, wait 15 minutes, reconnect
and attempt to power on
5. Replace the Power Supply
Problem – pH Probe Inaccurate
Follow the steps below until a solution is reached:
1. Ensure the pH probe is connected to the GrowBoss and
locked into place
2. Ensure probe and solution are the same temperature, this
can take up to 15 minutes
3. Ensure the probe to meter connection is not soiled. Clean
with compressed air
4. Ensure the probe is clean. See cleaning instructions
5. Calibrate your Growboss following the calibration guide
6. Rehydrate your pH Probe following the rehydration guide
7. Replace the pH Probe
Problem - Temperature Inaccurate
Follow the steps below until a solution is reached:
1. Ensure device is set to either Celsius or Fahrenheit,
depending on your preference
2. Ensure probe and solution are the same temperature, this
can take up to 15 minutes
3. Ensure the PPM probe is fully plugged into the meter
Problem - Nutrient reading is inaccurate
Follow the steps below until a solution is reached:
1. Ensure the device is set to display Nutrient in your preferred
method of display
2. Ensure probe and solution are the same temperature, this can
take up to 15 minutes
3. Ensure the probe to meter connection is not soiled. Clean with
compressed air
4. Ensure the probe pins are clean. See cleaning instructions
5. Calibrate your GrowBoss following the calibration guide
6. Ensure the PPM probe is fully plugged into the meter
7. Replace your Nutrient probe
11
Troubleshooting Guide
Problem - No Display
Follow the steps below until a solution is reached:
1. Check that the Growboss is connected to the 5dcv/0.5 amp
power supply
2. Check that the Power supply is connected to the wall outlet
3. Verify that the outlet has power by connecting another
device such as a lamp or fan
4. Unplug all cords and probes, wait 15 minutes, reconnect
and attempt to power on
5. Replace the Power Supply
Problem – pH Probe Inaccurate
Follow the steps below until a solution is reached:
1. Ensure the pH probe is connected to the GrowBoss and
locked into place
2. Ensure probe and solution are the same temperature, this
can take up to 15 minutes
3. Ensure the probe to meter connection is not soiled. Clean
with compressed air
4. Ensure the probe is clean. See cleaning instructions
5. Calibrate your Growboss following the calibration guide
6. Rehydrate your pH Probe following the rehydration guide
7. Replace the pH Probe
Problem - Temperature Inaccurate
Follow the steps below until a solution is reached:
1. Ensure device is set to either Celsius or Fahrenheit,
depending on your preference
2. Ensure probe and solution are the same temperature, this
can take up to 15 minutes
3. Ensure the PPM probe is fully plugged into the meter
Problem - Nutrient reading is inaccurate
Follow the steps below until a solution is reached:
1. Ensure the device is set to display Nutrient in your preferred
method of display
2. Ensure probe and solution are the same temperature, this can
take up to 15 minutes
3. Ensure the probe to meter connection is not soiled. Clean with
compressed air
4. Ensure the probe pins are clean. See cleaning instructions
5. Calibrate your GrowBoss following the calibration guide
6. Ensure the PPM probe is fully plugged into the meter
7. Replace your Nutrient probe
11

Nutradip GrowBoss Specifications

General

Brand	Nutradip
Model	GrowBoss
Category	Measuring Instruments
Language	English