©2024 Nuwave
®
LLC • All Rights Reserved.
Item: BQ47361-Rev1-V5-12-16-YK
Customer Service: For Amazon Purchases: support@nuwavenow.com ● For All Other Purchases: help@nuwavenow.com
To clean the surface underneath the
Inner Vent Screen.
1. Turn the OxyPure off and unplug it
from the wall outlet.
2. Lift the Top Vent using the built-in
tab.
3. Using a vacuum with a brush
attachment or duster, clean any
dust or accumulated particles from
the surface an Inner Vent Screen.
To clean the inner wall opposite of the
fan or to remove an object that has
fallen through the Inner Vent Screen.
1. After removing the Top Vent, locate
the two screws at the top of each
side of the vent.
2. Use a Phillips screwdriver to loosen
only the two screws shown on
the diagram to the right. Use the
magnetic tabs on the under side of
the Grid to set the screws.
3. Lift up the Inner Vent Screen.
4. After cleaning the inner wall with
a soft cloth or paper towel, or
duster. Reassemble the Inner Vent,
retightening the two screws, and
replace the Top Vent.
• Make sure all parts are secure
before plugging in the OxyPure and
turning it on again.
Cleaning the Top Vent
The Top Vent of your OxyPure can be removed to clean with a vaccum
with a brush attachement or cleaned in mild soapy water and dried
thoroughly.
Wi-Fi
Auto Scan Mode
1. Once you download the
Nuwave® Connect app, ensure
your phone is connected to
your home Wi-Fi network on the
2.4GHz or 5GHz frequency and
that your phone’s Bluetooth is on.
2. Turn on the OxyPure and activate
Wi-Fi Pairing Mode by pressing
and holding POWER until the
light next to the Wi-Fi symbol
begins to blink rapidly.
3. In the Nuwave® Connect app, tap
the + symbol, then tap Auto Scan
and select your device.
4. Enter your Wi-Fi network’s
password and tap Confirm. If the
connection is successful, the app
will display “Added Successfully”
on the screen.
Download the Nuwave Connect
App
This is an optional feature that is not
required to operate your OxyPure.
Using the QR reader in your Camera
App:
1. Scan the QR code below.
2. It will take you to the App’s download
page on either the Google Play Store
or the Apple AppStore, then just
follow the download and installation
instructions.
Downloading a QR reader App:
If your phone doesn’t have that capability
built-in, simply download a 3rd-Party QR
Scanning App before scanning the Nu-
wave QR Codes and you are ready to go.
1. Open your devices’ mobile app store
(Apple App Store or the Google Play
Store)
2. Search for “QR code readers.”
3. Simply download the QR code reader
to your phone, open it, scan the code
and you are ready to go.
The OxyPure is equipped to operate using WI-FI. This allows you to conveniently
operate your new air purier from nearly any location, whether at home or while
you are out and about, as long as you have a reliable Internet connection.
WiFi LED Status Light
Pairing Mode & Standby Mode
Solid Light.
The OxyPure is paired with the wi
network and ready to be used.
Rapid Blinking Light.
The OxyPure is in Pairing Mode.
The OxyPure will stay in Pairing Mode
for up to 10 minutes or until your device
is paired.
Slowly Blinking Light.
The OxyPure is in AP Pairing Mode.
No Light. The OxyPure’s WiFi is off.
Nu wave
®
Connect App (Optional) Cleaning & Maintenance
OXYPURE ZERO AIR PURIFIER
To Next Page
Need help?
General
