Ofna Racing DM-1 Spec User Manual

OFNA 7 VANDERBILT, IRVINE, CA 92618 PH: (949)586-2910 FAX: (949)586-8812.

Ofna Racing DM-1 Spec Specifications

General

Brand	Ofna Racing
Model	DM-1 Spec
Category	Motorized Toy Car
Language	English

Summary

Must Read Before Running

Initial Engine Starting Procedure

Step-by-step guide for the first-time engine start, emphasizing safety precautions.

Engine Break-in Process

Instructions for properly breaking in the engine to ensure longevity and performance.

Emergency Engine Stop Method

General Safety Precautions

Critical safety warnings and precautions for operating the RC model and its components.

Required for Operation

Setting Radio Neutral Position

Front Shock Absorber Assembly

Correct Front Shock Assembly

Detailed instructions for the proper assembly of the front shock absorbers.

Rear Shock Absorber Assembly

Correct Rear Shock Assembly

Front and Rear Differential Assembly (Part 1)

Front and Rear Differential Assembly (Part 2)

Front and Rear Gear Case Assembly

Servo Saver Assembly (Section 6)

Servo Saver Assembly (Section 7)

Servo Saver Assembly (Section 8)

Steering Tie-Rod Assembly (Section 9)

Servo Saver and Front Upper Arms Assembly (Section 10)

Front Shock Stay Assembly (Section 11)

Front Shocks Onto Shock Stay Assembly (Section 12)

Rear Shock Stay and Upper Arms Assembly (Section 13)

Rear Upper Arms Assembly (Section 14)

Rear Brace Assembly (Section 15)

Two Speed Gears Assembly (Section 16)

Two Speed Transmission Assembly (Section 17)

Two Speed Transmission and Center Diff. Mount Assembly (Section 18)

Brake and Center Diff. Mount Assembly (Section 19)

Arm Holder Onto Chassis Assembly (Section 20)

Front Lower Arms Assembly (Section 21)

Rear Lower Arms Assembly (Section 22)

Front and Rear Gear Box Onto Chassis Assembly (Section 23)

Front Knuckle Arms Assembly (Section 24)

Front Suspension Arms Assembly (Section 25)

Front Push Rods Assembly (Section 26)

Rear Wheel Hub Assembly (Section 27)

Rear Suspension Arms Assembly (Section 28)

Rear Shock Absorber Assembly (Section 29)

Two Speed Transmission Onto Chassis Assembly (Section 30)

Clutch Assembly (Section 31)

Clutch Assembly (Section 32)

Engine Onto Chassis Assembly (Section 33)

Manifold Onto Engine Assembly (Section 34)

Fuel Tank Onto Chassis Assembly (Section 35)

Radio Tray Assembly (Section 36)

Radio Tray and Receiver Box Assembly (Section 37)

Throttle Linkage Assembly (Section 38)

Throttle Linkage Into Servo Assembly (Section 39)

Steering Rod Into Servo Assembly (Section 40)

Radio Tray Onto Chassis Assembly (Section 41)

Front Bumper Assembly (Section 42)

Front Bumper Assembly (Section 43)

Front Bumper Assembly (Section 44)

Rear Bumper Assembly (Section 45)

Rear Bumper Assembly (Section 46)

Rear Bumper Assembly (Section 47)

Air Filter Assembly (Section 48)

Fuel Tube Assembly (Section 49)

Tires and Wheels Assembly (Section 50)

Wheels Onto Front Knuckle and Rear Hub Assembly (Section 51)

Body Assembly and Painting (Section 52)

Body Mounting Procedure (Section 53)

Final Body Mounting (Section 54)

Engine Starting Guide (Section 55)

Safe Model Operation Guidelines

Pre-Operation Checks

Engine Start-Up Procedures

During Model Operation

Safety Warnings and Precautions

Critical safety advice covering water operation, electrical issues, and model control.

Post-Operation Maintenance

Vehicle Setting and Tuning Guide

Front and Rear Toe Adjustment

Camber Angle Adjustment

Shock Angle and Suspension Stiffness

Force 28 Pull Start Engine Operation

New Engine Break-in Procedure

Detailed steps for breaking in a new engine to ensure optimal performance and durability.

Engine Needle Valve Settings

Guidance on adjusting the main and low-speed needles for fuel mixture and performance.

Barrel Stop Screw Idle Adjustment